Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Enterprise Homeowners
A gate that won’t open is a driveway you can’t use and a property that stops feeling secure. Most of the calls we take in Enterprise come down to a handful of familiar failures: a hinge post that has started to lean, an opener that strains and quits, or a latch that no longer lines up with the striker. Our technicians have up to 25 years of experience, and we’re equipped to handle electric gate repair and automatic gate repair throughout Enterprise, with same-day service available on most repair calls. Call (833) 780-1547 and a live person picks up – day, night, or weekend.
What Our Gate Repair Service Includes
Every repair starts with a look at the gate as a system, not just the part that’s misbehaving. A gate that swings crooked usually has a post problem. A gate that won’t latch usually has an alignment problem. Fix one without the other and you’ll be back on the phone in a month. Here’s what each of our repair services covers.
Electric Gate Repair
Electric gate repair covers the wiring, control board, transformer, and low-voltage connections that tell an automatic gate what to do. You need it when a gate clicks but doesn’t move, moves partway and stops, or behaves differently depending on the time of day. We trace the circuit from the control box to the operator, test the limits and safety devices, and repair the fault at the source instead of swapping a board and hoping.

Automatic Gate Repair
Automatic gate repair is about the operator itself: the motor, gearbox, drive chain, and the limit switches that tell it when to stop. This is the work you need when the gate opens slowly, grinds, reverses on its own, or won’t respond to the remote. We open the housing, check the gearbox for wear, test the torque setting, and adjust the travel limits so the gate stops where it should, not an inch past.

Hinge & Post Repair
Hinge and post repair fixes the gate at the point where it hangs, because a gate sags in the hinge post, not in the middle. You need it when the gate drags, the post leans, or the hinges are wallowed and the gate wobbles. Enterprise has a lot of older stucco-and-masonry walls holding up gate posts, and those posts get wet at the base and rot from the inside out. We expose the post, weld or replace the hinge, and reset the post so the gate hangs true again.

Gate Realignment
Gate realignment gets the gate to close flat and latch cleanly against the striker without dragging or binding. You need it after a hard hit from a car, after years of settling, or after a previous repair left the gate hanging crooked. We measure the gap top and bottom along the closing edge, shim and adjust the hinges, and true the frame so the latch catches the way it was designed to.
Lock Repair
Lock repair covers the mechanical latch, deadbolt, and keypad hardware on manual and automatic gates. You need it when the key sticks, the latch won’t spring back, the keypad stopped reading codes, or the lock no longer lines up with the striker. We clean and re-key mechanical locks, replace worn latch cams, and test the keypad against the control board – often the code reader is fine and the board is what’s failing.
Weld & Rust Repair
Weld and rust repair rebuilds the steel that holds the gate together – the corners, the stiles, the hinge brackets, and the bottom rail where water pools. You need it when you see bubbling paint, orange stains running down the panel, or a hinge that has torn away from the frame. We weld on site in your driveway so the gate never leaves the property, grind the joint clean, and coat the repair so it doesn’t rust back through next season.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Repair
We service LiftMaster operators and know where their control boards tend to fail first – usually the surge protection on the low-voltage side after a summer storm. FAAC and BFT equipment is common on heavier slide gates around Enterprise, and we know those gearboxes well enough to hear a worn bearing before it seizes. Mighty Mule swing operators show up on a lot of residential driveways, and their limit switches are the first thing we check when a gate reverses or stops short.
Whether you have a LiftMaster, a FAAC, a BFT, a Mighty Mule, or any other make, we can help. If the brand isn’t one we know cold, we’ll tell you straight and figure it out before we quote you a price – not after.
Signs You Need Gate Repair Right Now
- The gate drags or scrapes the ground. A gate that scrapes is a gate hanging off a failing hinge post. Left alone, the post keeps sinking and the gate tears itself apart at the hinges.
- The opener strains, hesitates, or reverses on its own. An operator that reverses mid-travel is a safety device doing its job – it thinks it hit something. It’s telling you the gate is binding, the limits are off, or the motor is failing.
- The gate won’t latch or the key sticks. A latch that misses the striker is an alignment problem nine times out of ten. It’s cheap to fix early and expensive once the gate has been slamming into the post for a season.
- You see rust stains or bubbling paint at the hinges or corners. Rust starts inside the tube where you can’t see it. Bubbling paint is the last warning before the steel gives way at a weld.
- A gate that used to open on its own now needs a shove. That shove is the operator’s torque giving out. Continuing to push it by hand wears the gearbox and turns a small repair into a motor replacement.
Our Gate Repair Process – Step by Step
- 1
We answer the phone and listen. A live person takes your call, 24/7, and asks what the gate is doing – not what’s wrong with it. The symptom tells us more than most customers expect, and it helps us bring the right parts on the first visit.
- 2
We diagnose on site before we quote. We test the operator, check the control board voltage, measure the gate for square and plumb, and probe the hinge posts at the base. You get a written price before any work starts, so nothing on the invoice is a surprise at the door.
- 3
We weld and repair on site, in your driveway. Whenever the repair can be done without hauling the gate away, that’s what we do. On-site welding means the gate stays put, the post stays in the ground, and you don’t lose a week waiting on it to come back.
- 4
We test the whole gate, not just the broken part. After the repair, we cycle the gate open and closed, test the safety edges and photo eyes, check the latch, and confirm the travel limits. If something adjacent is about to fail, we’ll show you now rather than let you find out later.
- 5
We back it up with the 90-Day Done Right Promise. Every job carries the promise in writing. If the repair doesn’t hold, one call brings us back and we make it right.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Enterprise?
A typical hinge and post repair in Enterprise runs $250 to $650 depending on whether the post needs to be reset or replaced. Electric and automatic gate repair usually lands between $150 and $450 for a control board, limit switch, or safety sensor fix, and climbs toward $600 to $1,100 when the operator motor or gearbox needs to come out. Weld and rust repair on a steel gate typically runs $200 to $500, depending on how much metal has to be cut back and rebuilt. Lock and latch work is the cheapest visit, usually $95 to $200.
Several things move those numbers: gate weight and material, whether the operator is a swing or slide model, how much rust is under the paint, and whether the post is set in concrete or bolted to masonry. The best way to avoid overpaying is to get a written estimate before anyone touches the gate and to ask what happens if the price changes mid-repair – with us, it doesn’t. Our free estimate covers the full diagnostic, a written line-item price, and a walk-through of what we found. Every price is quoted and agreed before work starts, and standing offers include $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (833) 780-1547 for an exact quote on gate repair in Enterprise – estimates are free.
Gate Repair Near Enterprise – Our Service Area
We serve Enterprise and the surrounding communities, including Spring Valley, Winchester, and Paradise, with drive times that put most calls within a couple of days and same-day availability on repair work when the schedule allows. Henderson, North Las Vegas, and Summerlin are all part of the regular route, and we handle rural calls out in Sandy Valley and toward Boulder City on scheduled days. If you’re in Summerlin or Sunrise Manor and your gate won’t close, call and we’ll tell you honestly how soon we can get there. You can also see our full service overview for the wider area we cover.
Serving Enterprise, NV – Our Local Coverage Area
We serve Enterprise and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Repair in Enterprise
Gate repair is the work of diagnosing and fixing what’s making a gate malfunction, whether that’s the operator, the hinges, the post, the latch, the wiring, or the frame itself. It covers everything from electric gate repair and automatic gate repair to welding a torn hinge back onto a steel frame. The point is to fix the actual cause, not to sell you a new gate. If a repair can save the gate, we’ll repair it.
Most gate repairs are done in a single visit, usually two to four hours on site. Hinge and post repairs and welding jobs can run longer because we’re resetting a post or building up steel, but the gate is typically working again before we leave. If we find something that needs a special part, we’ll tell you the day and time we’ll be back, and we’ll be there.
Most gate repairs in Enterprise fall between $95 and $650, with operator and motor work running higher at $600 to $1,100. The exact price depends on the part, the gate’s weight and material, and whether the post is involved. We give a written price before any work starts, and it doesn’t change at the door. Call (833) 780-1547 for an exact quote – estimates are free.
Yes, we service LiftMaster, FAAC, BFT, and Mighty Mule equipment, along with most other major gate brands. We know where each brand tends to wear out and what parts we’re likely to need, which saves a second trip. If your gate won’t respond to a remote, call and we’ll walk through the symptoms over the phone.
Often yes. We answer the phone 24/7 and can usually schedule same-day service on repair calls in Enterprise when the schedule allows. A gate stuck open at night is a security problem, and we treat it that way. Call (833) 780-1547 and we’ll tell you the soonest we can be there.
Every gate repair carries our 90-Day Done Right Promise in writing. If the repair doesn’t hold within 90 days, one call brings us back and we make it right at no charge. It’s stated plainly, not buried in fine print. That promise is the whole reason we can say we’re a shop you’ll see again.
Clear any cars or obstacles from the gate’s swing or slide path so we have room to test it, and make sure we can reach the control box and the hinges. If you have the operator manual or a remote that came with the gate, have it handy – it helps us match the setup. Beyond that, just be there to walk us through what the gate has been doing. If you’d rather have the full range of options first, our Gate Repair in Enterprise page covers it start to finish.
Schedule Your Gate Repair Service in Enterprise Today
If your gate is dragging, sticking, or won’t open at all, call (833) 780-1547 and a live person will pick up. We’ll give you an honest answer about what’s wrong and a free, no-obligation estimate before any work starts. Same-day availability on most repair calls in Enterprise, 24/7 phone coverage, repairs done on site whenever possible, and every job backed by the 90-Day Done Right Promise in writing. You can also look at our nearby Gate Repair in Spring Valley and Gate Repair in Paradise pages if you’re outside Enterprise. Call today – we’ll be there.
Written by the team at Gatewood Fence & Gate Enterprise.