A Gatewood company - serving Enterprise, NV

Hinge & Post Repair in Enterprise, NV

Wood & steel frameWood & steel frame
Wrought ironWrought iron
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate
Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Hinge & Post Repair in Enterprise, NV

A sagging gate almost always points to the hinge post, not the panel. Hinge and post repair in Enterprise, NV typically runs $150 to $450 for a single gate, and we can usually tell you which part failed before we ever touch a wrench. That matters here, because a lot of gates around Enterprise get the panel straightened and the post left alone, and then they sag again six months later.

We fix the cause. If the post has heaved out of level, cracked at the base, or pulled its anchors out of the block, we deal with that first. If the hinges are worn flat or the welds have let go, the on-site welding rig handles it in your driveway. The gate stays put. You don’t pay to haul it off and you don’t pay for parts that didn’t need swapping. Our technicians have up to 25 years of experience, and every job gets the 90-Day Done Right Promise in writing. Call (833) 780-1547 for a free estimate.

This is a sub-service of our Gate Repair work, and it’s one of the most common calls we get on the east side of the valley.

When You Need Hinge & Post Repair

Most folks call us after living with the problem for a while. Here’s what tends to tip people over the edge:

  • The gate drags or scrapes on the ground. That’s a post problem more often than a hinge problem. When the hinge post leans, the whole gate swings out of plane and the bottom corner starts kissing the concrete. In Enterprise’s caliche-heavy soil, posts that weren’t set deep enough tend to walk out of plumb within a season or two.
  • The gate won’t latch without a lift. You shoulder it up an inch to get the latch to catch. That inch is the hinge post moving, and it gets worse with every cycle.
  • The hinge post is wobbly in the ground. Grab the post itself, not the gate, and push. Any movement at the base means the footing is giving out or the anchors have loosened. That one we do not recommend putting off.
  • Cracked welds at the hinge plates. Common on steel frames, especially where the hinge tab meets the corner gusset. A hairline crack turns into a broken hinge in a hurry once the gate is being operated by an opener.
  • Rust streaks and soft metal at the hinge. Enterprise is dry, but irrigation overspray and the occasional monsoon soaking find the same spots every year. Once the metal around the hinge thins out, the hinge pulls through.
  • A brand-new gate that was never hung right. We get called to correct hinge and post work somebody else left behind. It’s more common than you’d think, and it’s not hard to spot once you know what you’re looking at.

If your gate is an automatic one and the opener keeps reversing or straining, the hinge and post problem can fool the motor into thinking it’s hitting an obstacle. That’s worth reading our page on gate opener repair in Enterprise alongside this one, because we often find both issues in the same visit.

Our Hinge & Post Repair Process

The order matters here. Fix the panel without the post and you’ll fix it twice. Here’s how we work through a hinge and post job:

  1. Look at the gate closing on its own. Before we grab a single tool, we open the gate and let it swing. Whichever way it drifts tells us which post is out of plumb. A gate closing on its own is telling you exactly where it’s failing.
  2. Check the post footing and the hinge points. We probe the soil around the post base, check the anchors, and inspect every hinge for wear, play, and cracked welds. On steel gates we check the hinge plates and the frame corners. On vinyl and ornamental aluminum, we pay attention to post caps and internal reinforcement.
  3. Reset or reinforce the hinge post. Depending on what we find, that could mean re-setting the post in fresh concrete, adding a deeper footing, or reinforcing the existing post with a steel sleeve. When we’re working around a concrete pad or a block wall, we use anchor systems rated for that substrate rather than driving new holes and hoping.
  4. Repair or replace the hinges. Worn hinges get swapped. Cracked welds get ground out and re-welded on site. If the gate was drilled for a hinge type that doesn’t suit the frame, we fix that too.
  5. Re-hang and re-level the gate. We set the gate back on the repaired hinges, check the diagonal, and get the latch side lined up. This is where a lot of sloppy jobs stop early. Latching is the whole point.
  6. Cycle the gate under power. If there’s an opener, we run it through full open and close cycles and check the limits and force settings. A LiftMaster or FAAC operator that was fighting a sagging gate will behave differently once the geometry is right. We adjust it so it doesn’t over-travel or slam.

If your post is set into decorative block or a stucco wall, we may need to talk through the repair approach before we start. Our page on gate post repair in Enterprise goes deeper on the structural side of that work.

Hinge & Post Repair Pricing in Enterprise

Here’s what folks around Enterprise actually pay for hinge and post work. These are real ranges, not teaser numbers, and your free estimate locks in the price before we start.

Job Typical Range Notes
Hinge replacement (single gate, 2-3 hinges) $150 – $280 Includes hardware and re-hang
Weld repair at hinge or frame $175 – $320 On-site welding, gate stays in place
Hinge post reset in fresh concrete $250 – $450 Depends on footing depth and soil
Hinge post reinforcement (sleeve, plate, anchor) $200 – $380 For posts that are sound but moving
Full hinge and post rebuild (both sides) $450 – $750 Double gates, heavy ornamental steel

A few things move the number. Gate weight and material matter a lot: a light aluminum gate is a different job than a 300-pound ornamental steel double gate. Post substrate matters too. Setting a post into caliche is different from anchoring into a block wall or a concrete pad. And access matters. If your gate is down a long gravel drive with a tight turnaround, we’ll tell you up front if that affects anything.

What doesn’t move the number: we don’t quote one price on the phone and a different one at the door. Standing offers apply here too. That’s $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. If you’ve got a written estimate from another company, we’ll give you a free second opinion on it. Show us the paper and we’ll tell you straight whether it’s fair.

For a broader look at what gate work runs in this part of the valley, our gate repair cost guide for Enterprise lays out the full picture.

Why Fix the Post First

A gate sags in the hinge post, not in the middle. The panel is just following the post. Straighten the panel and leave a leaning post, and you’ve bought yourself a few months before it sags again. That’s the sloppy work we keep finding: hinges swapped, gate muscled back into level, post untouched. It looks fine when the truck pulls away.

Fixing the post first costs a little more up front sometimes. It saves you the second bill. We’d rather do the job once.

It also keeps your opener alive. A gate motor working against a sagging gate runs hot, chews through gears, and trips its force limits. We’ve replaced plenty of Mighty Mule and BFT operators that died young because the gate geometry was wrong and nobody fixed it. Fix the hinge and post, and the opener gets to do its actual job. For more on that side of things, see our gate motor repair in Enterprise page.

How Long Does Hinge & Post Repair Take?

Most single-gate hinge jobs are done in two to four hours. A post reset that needs fresh concrete takes longer, and we usually ask you to leave the gate out of service until it cures, which is typically 24 hours. We’ll tell you the timeline before we start, not after. If you’ve got a LiftMaster or FAAC opener on the gate, budget a little extra time for the limit and force adjustment at the end.

FAQs – Hinge & Post Repair

How much does hinge and post repair cost in Enterprise, NV?

Expect $150 to $450 for most single-gate hinge and post repairs in Enterprise, with full rebuilds on heavy double gates running $450 to $750. The exact price depends on the gate weight, the post substrate, and whether the failure is the hinge, the post, or both. Call (833) 780-1547 for an exact quote, and the estimate is free.

Can you repair the post without replacing the whole gate?

Yes, in most cases. A post that’s out of plumb or has loose anchors can usually be reset or reinforced without touching the gate panel. That’s the whole point of fixing it post-first. If the post footing is completely gone, we’ll walk you through what rebuilding it involves. Either way, you’re not paying for a new gate over a fixable post.

Do you weld on site, or do you take the gate away?

We weld on site, in your driveway. Cracked hinge welds, broken hinge tabs, and frame repairs all get handled where the gate lives. Hauling a gate off means a gap in your fence line and a longer job, and it’s rarely necessary. On-site welding is part of why we can turn most hinge repairs around in a single visit.

Will my gate opener work properly after the repair?

It should, once the hinge and post are right and we’ve reset the opener’s limits and force. A gate that was sagging makes the operator work harder than it was designed to. After a hinge and post repair, we cycle the gate under power and adjust it so it opens and closes cleanly. If the opener itself is worn out from running a bad gate, we’ll tell you. We’re certified to service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we know what we’re looking at.

What if a hinge post is set in a block wall or decorative column?

It’s a more involved repair, but it’s very doable. We anchor into the block or reinforce the column rather than driving new holes and hoping they hold. Our team walks through the structural options with you before any work starts, and the estimate covers it. If you’ve got a decorative column, it’s worth a look at our gate column repair in Enterprise page too.

Gates We Repair Around Enterprise

We work on all the gate types you’ll find in Enterprise and the surrounding communities, including:

  • Ornamental steel and wrought iron driveway gates
  • Vinyl and composite privacy gates
  • Aluminum single and double swing gates
  • Automatic driveway gates with LiftMaster, FAAC, BFT, Mighty Mule, and other openers
  • Pedestrian and pool safety gates
  • Custom gates that need a hinge or post repair

If you’re elsewhere in the valley and want the same post-first approach, we also handle gate repair in Henderson, gate repair in North Las Vegas, and gate repair in Summerlin. If you’re just getting a new gate and want the hang done right the first time, our gate installation in Enterprise page covers that. And if you need hardware or a new set of hinges before we get out there, our gate parts and welding in Enterprise page has the details. Back at the home page, you can see the full range of what we do.

Contact Gatewood Fence & Gate Enterprise

If your gate is dragging, won’t latch, or has a post that wobbles when you push it, call (833) 780-1547. A live person answers, day or night. We’ll set a window and show up in it. Every job carries the 90-Day Done Right Promise in writing, and if something isn’t right, one call brings us back. The estimate is free, and the price you hear is the price you pay.

Written by the team at Gatewood Fence & Gate Enterprise, serving Enterprise.

Need Gate Repair help in Enterprise? Licensed & insured · 30-60 min response · free estimates
Call (833) 780-1547
Local Service Coverage

Request a Free Estimate in Enterprise

Tell us what you need - Gatewood Fence & Gate Enterprise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch