Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Access Control for Enterprise Homeowners
Gate access control in Enterprise comes down to one question most homeowners never think about until it fails: who gets in, and how do they prove it? We work on keypads, remotes, card readers, phone entry and smart access for gates all over the east valley, and our technicians bring up to 25 years of hands-on experience to the jobs that other outfits walk away from. The person who shows up knows how to trace a dead keypad back to the transformer instead of selling you a whole new board. Same-day repair is available in Enterprise on most calls, and a free estimate is standard. Call (833) 780-1547 and you’ll get a live person, any hour.
What Our Gate Access Control Service Includes
Access control is the part of a gate system that decides whether the gate opens for you or stays shut. It’s also the part that fails in small, confusing ways. Here’s what we handle under this category.
Keypad Entry
A keypad lets anyone with the code in, and nobody without it. When a keypad starts skipping digits, taking two tries to register, or just won’t read at all, it’s usually a worn membrane under the buttons or moisture in the housing, not a signal problem. We open the unit, check the wiring back to the operator, and test every key under load before we call it done. If the pad is genuinely at the end of its life we’ll tell you that plainly, and if replacing one part fixes it we’d rather do that.

Remote Control
Remotes are the most convenient entry there is right up until the range shrinks to ten feet or one remote stops working while the other is fine. That pattern almost always points to a failing receiver at the operator, a battery on its last legs, or interference from a neighbor’s equipment on the same frequency. We pair, re-pair and test remotes on site, and we can walk a stubborn one through re-pairing over the phone if you’d rather not wait for a visit.

Phone Entry
Phone entry lets a resident open the gate for a visitor from anywhere by picking up a call. It’s common on gated driveways with a home office or a long approach where a keypad at the road is impractical. When a call-box setup stops ringing through, the cause is usually a phone line, a cellular module, or a handset that has gotten wet in a desert storm. We trace the connection, verify the ring-through to your handset, and test the release before we leave.

Card Reader
Card readers are the next step up from a keypad: a card is harder to share than a code and easier to revoke when a contractor or a family member no longer needs access. We install and repair proximity readers and their wiring, check the read range, and confirm the door and reader are talking to the same controller. When a reader works on one card and not another, the problem is often the card, not the reader, and we check the cheap items first.
Video Intercom
A video intercom lets you see who’s at the gate before you open it. That matters most on a driveway where you can’t see the entrance from the house. We install and service intercom cameras, monitors and door-release wiring, and we test the picture and the release separately, because the failure modes are different. If you’re getting a picture but no release, that’s a wiring or controller problem, and we’ll trace which one it is rather than guess.
Smart Access
Smart access means opening and closing the gate from a phone app, scheduling access, and getting a log of who came and went. We integrate smart controllers with LiftMaster and FAAC operators, set up app access, and make sure the manual release still works when the network is down. A gate that depends on Wi-Fi is a gate that needs a manual release you can trust, and we won’t hand one back to you without testing it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Access Control
We work on the access control side of nine major gate brands, and knowing how each one fails saves you from replacing parts that are fine. On Mighty Mule keys and receivers, the weak point is usually the battery contacts and the older non-code-hopping remotes, and we can tell you which of the two you’re dealing with in minutes. On LiftMaster operators, the receiver board and the paired remote are the spots we check first when range drops, and we keep re-pairing procedures for their model lines down cold.
With FAAC equipment, the access board and controller wiring are where most of our diagnostic time goes, particularly on older systems where a previous owner added a keypad or intercom that was never documented. And whether you have BFT, LiftMaster, Mighty Mule, FAAC or any other make, we can help. That includes systems where the brand plate is gone and the only way to identify the gear is by the shape of the board or the number of terminals. We figure it out and tell you the truth about what’s on the gate.
Signs You Need Gate Access Control Right Now
Access control problems rarely start with a gate that stops dead. They start with small annoyances that get worse. Here are the warning signs worth taking seriously.
- The keypad takes two tries to register a code. That is usually a worn membrane or moisture inside the unit, and it tends to fail completely within weeks rather than months. Fixing it now is a small job; dealing with it when the gate won’t open on a contractor’s delivery is a bigger one.
- Remote range shrinks a little each month. Weak range points to a receiver going bad or an antenna that’s been damaged or moved. Left alone, it gets to the point where you’re rolling down the window and stretching to get a signal.
- One remote works and one doesn’t. That pattern usually means a receiver or a remote that needs re-pairing, not a dead operator. It’s the cheapest fix on this list and the one people most often skip.
- The intercom rings but never releases the gate. A call that connects but won’t open means the door-release wiring or the controller is the problem, not the phone side. That’s a safety issue when you need the gate open for emergency access.
- Cards that used to work stop working. A reader that’s selective about which card it accepts points to the reader, the card, or the controller in that order. We test each one before recommending a replacement.
Our Gate Access Control Process – Step by Step
Every access control visit follows the same order, because checking the cheap stuff first is how you avoid paying for parts you didn’t need.
- 1
We listen and look before we touch anything. We ask what changed and when, then we watch the gate cycle and watch you use the keypad or remote. A gate that hesitates on the last third of its travel tells us more than a meter reading.
- 2
We check power first. Dead keypads, blank readers and remotes that stopped working are usually a blown transformer, a tripped breaker or a corroded connection at the operator. We meter the supply at the gate and at the house before we pull a panel.
- 3
We test each access point separately. Keypad, remote, intercom and card reader each get cycled on their own. Isolating one from the other is how you find out whether the problem is in the device or in the line back to the controller.
- 4
We trace the wiring and re-pair what needs re-pairing. A continuity tester finds the break, a receiver scan finds the interference, and a fresh programming pass on the remotes settles most of the rest. We document what we changed.
- 5
We test the manual release and the full cycle before we call it done. A gate that opens on an app is useless if the manual release is frozen or the safety edge doesn’t reverse. We cycle the gate with the safety edges blocked and verify the reversal before we leave.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Enterprise?
Most access control work in Enterprise falls into a handful of price bands, and the band depends on whether you’re fixing a device or adding a new one. Re-pairing and testing remotes is typically the cheapest visit. Replacing a keypad or a single reader, including the wiring check, runs in the low to mid hundreds. Adding phone entry, a video intercom or smart access with app control is a larger job because it involves mounting, wiring and commissioning, and it’s the kind of work we measure and quote before anything gets ordered.
- Remote re-pairing and diagnosis: the smallest job we do, often folded into a repair call.
- Keypad or card reader replacement: device plus wiring and commissioning.
- Phone entry or video intercom install: handset, camera, wiring run and release test.
- Smart access integration: controller, app setup and manual release verification.
What moves the price is the wire run length from the house to the gate, whether the operator can talk to a new controller, and whether a previous install left undocumented wiring behind. The other thing that moves it: we don’t quote one price on the phone and a different one at the door. The price is quoted and agreed before any work starts, and if a part turns out not to need replacing, we take it off the bill. A free estimate means we look, we tell you what it takes, and you decide. Call (833) 780-1547 for an exact quote, and the $40 off any repair over $200 standing offer applies. Seniors and veterans get a permanent 10% off.
Gate Access Control Near Enterprise – Our Service Area
We work gate access control throughout Enterprise and the surrounding towns, including Spring Valley, Paradise, Summerlin, Winchester, Henderson, Whitney and Sunrise Manor, with jobs reaching out to Las Vegas, North Las Vegas and Boulder City. If you’re further out toward Sandy Valley, call and we’ll tell you honestly when we can get there. Same-day repair is available on most calls in Enterprise. For access control work around the rest of the valley, see Gate Access Control in Spring Valley and our home gate services page for the full range of what we do.
Serving Enterprise, NV – Our Local Coverage Area
We serve Enterprise and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Access Control in Enterprise
Gate access control is the equipment that decides who can open your gate and how: keypads, remotes, phone entry, card readers, video intercoms and smart-access controllers. It sits between the person at the gate and the operator that actually moves the gate. We repair and install all of it, and we test the manual release on every job. Call (833) 780-1547 for a free estimate.
Most repair calls are done in a single visit of an hour or two, and same-day service is available in Enterprise on many of them. New installs, phone entry, video intercom and smart access are scheduled work, because the equipment has to be measured and quoted before it’s ordered. We’ll tell you the honest timeline at the estimate and we’ll show up in the window we promised. Call (833) 780-1547 to book a measure.
Repair and re-pairing visits are the low end, keypad and reader replacements run in the low to mid hundreds, and phone entry, intercom or smart access installs are quoted separately after a measure. The price is quoted and agreed before any work starts, never a surprise at the door. A free second opinion on any written estimate is also standard, and there’s no trip charge inside the county. Call (833) 780-1547 for an exact number.
Yes. We service LiftMaster alongside FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule, and we know where each brand’s access hardware tends to wear out. On LiftMaster, that’s usually the receiver and the paired remote when range drops. If your brand isn’t on that list, call anyway and we’ll tell you whether we can help. Call (833) 780-1547.
Yes. A live person answers the phone 24 hours a day, 7 days a week, and never a voicemail or an out-of-state queue. If a gate is stuck open or a resident is locked out, call and we’ll get you on the schedule. Same-day repair is available in Enterprise on most emergency calls. Call (833) 780-1547 and you’ll get a person.
Every job carries the 90-Day Done Right Promise in writing. If something we fixed isn’t working the way it should within that window, one call brings us back and we make it right, no runaround. That’s not “in most cases” or “up to” – it’s the plain promise, stamped on the invoice. Call (833) 780-1547 to set up the visit.
Have every remote, card and code in one place, and write down what changed and when, because that saves diagnostic time. Clear the path from the driveway to the keypad and the operator, and let us know about any gate code or lock we’ll need to get through. If a previous owner left wiring behind, we’ll sort it out on site. Call (833) 780-1547 with any questions before the visit, and see Gate Access Control in Paradise for another nearby service area.
Schedule Your Gate Access Control Service in Enterprise Today
If your keypad is skipping, your remote is fading or you’re ready to add phone or smart access to your gate, call (833) 780-1547. A live person answers any hour, same-day repair is available in Enterprise on most calls, and the estimate is free with no obligation. The price is quoted and agreed before any work starts. Gate, Gate Repair and Gate Installation work all fall under the same 90-Day Done Right Promise, and if you want to talk about a motor or opener instead, our Gate Motor & Opener page explains what we do there.
Written by the team at Gatewood Fence & Gate Enterprise.