Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Motor & Opener Across Henderson
If your gate won’t open, won’t close, or stops halfway and beeps at you, we can help. We work on gate motors and openers all across Henderson – from the older single-story blocks near Water Street to the stucco tract homes off Horizon Ridge in Seven Hills and the newer builds up in Anthem. We know this city’s gates, we know its soil, and we know what its HOAs will and won’t approve. Most repair calls get a real look the same day, and you’ll talk to a live person when you call (833) 780-1547. No voicemail, no phone tree.
Why Gatewood Fence & Gate Enterprise Is Henderson’s Preferred Gate Motor & Opener Company
We’ve built our name in Henderson one driveway at a time, and it shows in the calls we get from neighbors passing our number along. When we show up, you get a straight read on what’s wrong and a price quoted before anything gets touched – the number on your estimate is the number on your invoice. Our technicians have up to 25 years of experience, and we service nine major gate brands, so a 1990s LiftMaster or a newer FAAC doesn’t send us running.
Henderson homeowners have been burned before by outfits that quote one price on the phone and charge another at the door. We don’t play that game. Every job carries the 90-Day Done Right Promise in writing, and one call brings us back if something isn’t right. We also keep standing offers on the table: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate you’ve already got, and a permanent 10% discount for seniors and veterans.
What makes the difference in Henderson is knowing the ground and the rules. Anthem and Seven Hills sit on expansive desert soil that shifts as it dries, and the gate posts move with it. Green Valley and Anthem have design-review committees that care what your gate looks like, not just whether it opens. That combination is why a motor swap here is rarely just a motor swap. It’s also why we hand you the same person’s cell number and mean it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Motor & Opener Services in Henderson
Motor Repair
Most failed operators don’t need to be replaced – they need a real diagnosis. In Henderson’s older stucco-on-frame neighborhoods, an operator often quits when a 1990s control board gives out after years of 100°F-plus summers, leaving the gate stuck open or cycling on its own. We test the board, check the safety photocell alignment, and look at the mechanical side before we recommend anything. Sometimes a hinge post has shifted and the motor is fine – the gate’s just dragging. This is our most common Henderson call, and it’s where our repair-first approach saves you the most.

Motor Installation
When a unit genuinely predates modern UL 325 entrapment protection, or the board is obsolete and no compatible retrofit exists, a new operator is the cheaper answer over the long run. We measure the gate, match the operator to its weight and swing, and handle the power run and safety devices. Installation is scheduled, not rushed – we give you a free measure and a written price before anything gets ordered. We service LiftMaster, FAAC, and Mighty Mule units regularly, and we’ll tell you plainly which one fits your gate.

Linear Motor
Linear operators are common on Henderson’s ornamental steel and side-yard gates, and they hold up well until UV and dry heat start working on the seals. We repair and replace Linear motors, source compatible boards when they’re available, and re-hang gates that have thrown the operator out of alignment. If your Linear unit is cycling erratically, there’s usually a reason beyond the motor itself.

Slide Motor
Slide gates need a level track and a straight post to run clean, and in Henderson the ground doesn’t always cooperate. We service slide operators, check the rack and pinion for seized or rusted sections, and re-level tracks that have heaved after a monsoon or a dry spell. When a slide gate drags, the operator is often the victim, not the cause.
If you want to see the full range of what our Gate Motor & Opener team handles, it’s all on the service page. And if you’re new to the area, you can read more about Gate Motor & Opener in Henderson on our city page.
Trusted Brands We Service in Henderson
We’re certified to service nine major gate brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters in Henderson because the gates here span decades – you’ll find a 1990s LiftMaster in one yard and a fresh BFT swing operator in the next. We don’t claim to stock parts locally; anyone who tells you they do is probably guessing. What we do is diagnose fast, source what’s needed, and get you a straight answer on turnaround. When a board has to be ordered, we tell you the window up front instead of leaving you guessing.
Common Gate Motor & Opener Problems We See in Henderson Homes
- Obsolete control boards in pre-2000s operators. Sustained 100°F-plus summers cook these boards until they overheat and fail, and the gate ends up stuck open or cycling randomly. A retrofit board sometimes saves the unit; sometimes it’s the signal that the operator is past its years.
- Hinge posts that shift in the desert soil. On golf-course-adjacent lots in Seven Hills and Anthem, expansive soils dry and settle, and the hinge post moves with them. The swing gate starts to drag, the operator strains to push it, and eventually the motor takes the blame for a post problem.
- Faded powder-coat and dried-out seals. Intense UV and near-zero humidity fade finishes and dry seals, and then a monsoon downpour flash-rusts the hinges and seizes the rack and pinion. This is where a little maintenance goes a long way.
- Posts thrown out of plumb by ground settling. The rare winter freeze and the wet-dry cycle both push posts out of true. A gate that looks fine can drag its swing arm on one side and not the other – that’s the tell.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Motor & Opener in Henderson, NV
Here’s what the work actually runs in this market, quoted before we start. A board or control repair typically runs $180 – $360. A photocell or safety-device fix is usually $120 – $250. Hinge-post re-plumbing and re-hanging a dragging swing gate runs $250 – $550 depending on the post and hardware. A full operator replacement, installed, usually lands between $650 and $1,400 – Linear and Mighty Mule swing units sit at the low end, LiftMaster and FAAC at the higher end once safety edges and the power run are included. A battery backup add-on for a solar or standard opener runs $150 – $400. HOA paint or color-matched refinishing on a repaired gate adds $80 – $200 when the design review requires a specific approved finish. Every price is quoted and agreed before we touch a thing. Estimates are free, and so is a second opinion on any written estimate you already have.
We Also Serve Cities Near Henderson
We take calls throughout the area around Henderson, including Boulder City, Whitney, Paradise, and Enterprise. If you’re just outside the city line, call and we’ll tell you honestly whether we can get to you and when. No trip charge inside the county. Same straight pricing wherever you are.
Serving Henderson, NV – Our Local Coverage Area
We serve Henderson and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Motor & Opener in Henderson
Often it can be retrofitted, but not always, and the honest answer depends on the unit. If a compatible board exists for your LiftMaster or Linear operator and the rest of the unit is sound, a retrofit is the cheaper fix, usually $180 – $360. If the operator predates modern UL 325 entrapment protection, though, a retrofit board doesn’t make it a safe gate – replacement is the better call, and it protects the people and pets walking through. We’ll check the safety devices before we recommend anything. Call (833) 780-1547 for a free estimate.
Because the motor probably is fine – it’s the post that’s moved. In Anthem and Seven Hills the expansive desert soil dries and settles, the hinge post shifts, and the swing gate starts to bind and strain the operator. The fix is re-plumbing the post and re-hanging the gate, not swapping parts that don’t need swapping, and it usually runs $250 – $550. Left alone, the drag will eventually wear out the motor too. Call (833) 780-1547 and we’ll look at the post first.
Yes, in Green Valley and Anthem in particular, the association reviews the gate’s color, style, and setback – so even a motor replacement has to keep the approved look. Hidden arms may be required, paint colors may be specified, and some communities restrict visible hardware. This is the constraint that separates Henderson from Las Vegas-proper or Boulder City, and it’s why we match the approved palette and style before we order anything. A qualified operator that also clears design review is the goal. Call (833) 780-1547 for a free measure and a written price.
Heat is hard on backup batteries, and 100°F-plus summers shorten their life noticeably. Sealed lead-acid batteries in a Henderson gate operator often need replacement well before the manufacturer’s rated life, and solar panels gather dust that cuts their charging. A battery backup add-on runs $150 – $400. If your gate free-fails during a power outage, the battery is the first thing to test. Call (833) 780-1547 and we’ll check it.
Automatic gates should have entrapment protection that meets UL 325 – typically a photo-eye (photocell) pair, and often safety edges on the gate itself. You can check yours by breaking the beam while the gate is closing: the gate should stop or reverse. If it keeps closing, the safety device isn’t working. Don’t test it with a person or pet in the way. Get a professional to align or replace the device, usually $120 – $250. Call (833) 780-1547 for a free estimate.
Get Your Henderson Gate Motor Fixed Right
Whether it’s a 1990s operator that finally gave out, a swing gate dragging in Seven Hills, or a battery backup that quit during the last outage, we’re ready to help. You’ll talk to a live person when you call, and you’ll get a price quoted before any work starts. Same-day and emergency availability, free estimates, and the 90-Day Done Right Promise on every job. Call us at (833) 780-1547 and let’s get your gate moving again.
Written by the team at Gatewood Fence & Gate Enterprise.