Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterAutomatic Gate Repair Cost in Enterprise, NV: What You’ll Actually Pay
Most automatic gate repairs in Enterprise run $150 to $400, and the single biggest reason a bill climbs past that is HOA compliance – not the broken part. If a previous tech used the wrong powder-coat color or mismatched ironwork, your association can flag it, and you pay for the repair twice. Call Gatewood Fence & Gate Enterprise at (833) 780-1547 for a free estimate with upfront pricing, no trip charge inside the county, and a second opinion on any written quote you already have.

Enterprise is a master-planned, HOA-heavy suburb of Las Vegas, and that changes what gate repair costs here. Almost every driveway gate, community entry gate, and side-yard gate sits under recorded CC&Rs that dictate style, color, and placement. The gates themselves went in fast during the 1990s and 2000s tract boom, which means a technician works block after block of identical gates – and the roller that wore out on your neighbor’s unit is wearing out on yours. Add Mojave summer heat above 100°F and wind-blown sand off the open desert edge, and you get a steady stream of the same failures. We see it every week in Gate Repair in Enterprise.
What Drives the Cost of Automatic Gate Repair in Enterprise?
The part is rarely the whole story. What you pay depends on which component failed, how the gate is set in the ground, and whether the fix has to match your association’s approved spec. Here’s where the money actually goes on the failures we handle most.
| Failure type | Typical cost |
|---|---|
| Roller replacement (sliding gate) | $80-$150 |
| Control board burnout from summer heat | $200-$350 |
| Photo-eye realignment after monsoon wind | $75-$125 |
| Post re-setting in caliche soil | $250-$500 |
Why these four? The wind-and-sand combo off the desert edge chews through sliding-gate rollers and knocks photo-eye sensors out of alignment. Heat bakes operators, solar panels, and control boards. Flash-flood rain events shift gate posts set in caliche-heavy desert soil, and that’s the repair people put off longest – until the gate won’t close at all.
The HOA Compliance Multiplier
Here’s the part a generalist misses. In an Enterprise HOA community, a gate isn’t just a gate – it has to match the approved iron or vinyl design and color recorded in your CC&Rs. If a tech grabs whatever’s on the truck and it doesn’t match, your association can require a re-repair. That’s the repair bill plus the do-over, and it’s why knowing the approved spec before anyone touches the gate is worth more than a low first quote. A repair-first specialist who stocks HOA-common components and knows the local spec will almost always land below a swap-everything quote. Our crews handle Viking, Ghost Controls, DoorKing, and Elite operators and the ironwork that goes with them.
Why a Repair-First Quote Usually Costs Less
A replacement-first tech will tell you the motor’s shot when the real problem is a board that needs a reset or a capacitor that costs a fraction of a new unit. That swap runs $400-$800 more than a proper repair, and it happens more than it should. Our approach is to diagnose before anything gets priced.
The gate sags in the hinge post, not in the middle – that’s where we start. Fix the panel without the post and you’ll fix it twice. We weld on site so the gate stays in your driveway rather than getting hauled off or swapped for parts it doesn’t need. On site welding matters here: a lot of these community gates are cycled 50+ times a day, and a weld done in the driveway holds up better than a bolt-on patch.

What the Visit Actually Looks Like
- Diagnose the failure. We check the operator, the board, the photo-eyes, the rollers, and the posts before quoting anything.
- Check the HOA spec. Color, style, and hardware have to match your association’s approved design, or the fix won’t pass.
- Give you upfront pricing. No haggling, no surprise at the door – the number we quote is the number you pay.
- Repair on site. Welding and component swaps happen in your driveway, not at a shop across the valley.
- Back it in writing. Every job carries the 90-Day Done Right Promise stamped on the invoice.
How Much Should You Budget for a Community or HOA Gate?
Community gates are a different budget from a single driveway. Because they cycle dozens of times a day and sit exposed to full sun, they fail more often – and the fixes tend to be structural. A worn roller on a shared gate gets replicated across neighbors’ units in Enterprise, so a single call often turns into a cluster of repairs. The 90-Day Done Right Promise matters here: if a fix fails inside 90 days, we come back at no charge. That’s a plain statement, not a hedge – one call brings us back, no runaround. For a deeper look at how we handle failed operators and stuck gates, see our main Gate Repair page.
Standing offers that apply to every job, no haggling required: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. The second-opinion offer is the one that saves the most – bring us the quote someone else wrote and we’ll tell you straight whether it’s a repair or a replacement.
FAQs
Most automatic gate repairs in Enterprise fall between $150 and $400, with the exact number depending on the failure – a roller replacement runs $80-$150, a control board $200-$350, photo-eye realignment $75-$125, and post re-setting $250-$500. HOA compliance can push the bill higher if the fix has to match an approved color or style. Call (833) 780-1547 for an exact quote – estimates are free.
Repair is almost always cheaper when the operator and panel are sound and only a component has failed. A full replacement runs $400-$800 more than a board reset or capacitor swap, and many “dead” motors only need that. We diagnose first, so you’re not paying to replace a gate that just needed a repair. Call (833) 780-1547 and we’ll tell you which it is.
Same-day service is often available, and a live person answers every call 24/7 – not a voicemail, not a call center three states away. Call (833) 780-1547 and we’ll give you a real window and show up in it.
Yes. Because so many Enterprise gates fall under recorded CC&Rs, we check the approved spec before ordering parts so a compliant repair doesn’t turn into a re-repair. If your association flagged a previous tech’s mismatched hardware, we can match the recorded design. Call (833) 780-1547 with your gate details and we’ll take it from there.
Get a Straight Number Before You Commit
Don’t let an HOA spec or a hard-sell replacement quote run up your bill. The name is on the shop, the shop is down the road, and every job carries the 90-Day Done Right Promise in writing. Call (833) 780-1547 for a free estimate with upfront pricing and a second opinion on any written quote you’ve already got.
Written by the team at Gatewood Fence & Gate Enterprise, serving Enterprise, NV.
What Our Customers Say
"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo