Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Enterprise?
A gate motor or opener repair in Enterprise usually runs $180 to $525, and a full motor and opener replacement typically lands between $650 and $1,900 depending on the gate’s weight, the brand, and whether the operator arm and safety sensors need to be swapped out too. Most simple repairs are a single-visit job. If your gate is dead in the driveway right now, a call usually gets a live person on the line and a real number instead of a callback window.
Key Takeaways
- Motor and opener repair in Enterprise averages $180 to $525; replacement runs $650 to $1,900.
- Access control and keypad work adds $150 to $650 on top.
- Brand matters: LiftMaster, DoorKing, and FAAC parts sit at the higher end; Mighty Mule and Ghost Controls at the lower end for residential gates.
- A free second opinion on any written estimate is a standing offer, no haggling required.
Gate Motor & Opener Cost Breakdown (2026)
Below is what we actually see on invoices in the Enterprise area going into 2026. These ranges cover a standard residential slide gate or swing gate on a single-family lot. HOA and commercial operators push toward the top of each range.
| Line Item | Typical Price Range |
|---|---|
| Service call / diagnostic | $0 inside the county (no trip charge) |
| Opener motor repair (small parts, limit switch, capacitor) | $180 – $340 |
| Control board or receiver replacement | $260 – $525 |
| Full motor and opener replacement (residential slide gate) | $650 – $1,450 |
| Full motor and opener replacement (swing gate, dual arm) | $900 – $1,900 |
| Safety sensor / photo-eye replacement | $150 – $285 |
| Keypad or remote receiver install | $150 – $400 |
| Access control (card reader, intercom, telephone entry) | $280 – $650+ |
| On-site welding of hinge, post, or track | $150 – $400 |
What pushes a job up: a heavy wrought-iron gate that needs a bigger operator, a brand that requires a proprietary board, a hinge post that has shifted and is fighting the motor, or an access control panel that needs wiring run back to the house. What pulls it down: a motor that just needs a limit setting, a remote that needs re-pairing, or a sensor knocked out of alignment by a bump.
One pattern we see over and over in Enterprise: a gate that “started acting up” is blamed on the motor when the motor was doing its best against a hinge post that has rotated in the heat. Fix the post, and the motor behaves. That is why our approach starts with the gate itself, not the box on the wall.
What Affects Gate Motor & Opener Pricing in Enterprise
Enterprise sits in the Mojave heat band south of Las Vegas, and the local conditions shape what fails and what it costs to fix. The gate does not live in a vacuum.
- Summer heat and direct sun. Control boards and receiver modules cook on a sun-baked fence line. Motors mounted on the west side of a property near Mountain’s Edge or Rhodes Ranch fail earlier than shaded ones, so board replacements show up more often than in cooler climates.
- Gate weight and material. A steel slide gate over 400 pounds needs a heavier-duty operator. Wrought iron and solid metal panels cost more to automate than a lighter aluminum frame.
- Brand and parts availability. Enterprise is a newer build-out and lots of gates here came from builder packages. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so what is already in the ground usually has parts available. An off-brand operator with no local parts support turns a $300 fix into a $1,300 swap.
- Power and wiring. A gate operator needs 120V at the gate. If the run from the house has to be trenched in, that adds cost to the job. If you already have a dedicated circuit and a conduit at the post, you save.
- Access control. A basic keypad is simple. An HOA card reader or an intercom talking back to the house pushes a job higher. The Gate Motor & Opener in Enterprise page covers the access side in more detail.
- Gate alignment and hinge condition. A sagging swing gate fights the motor on every cycle and wears it out. Straightening and re-welding the hinge before the motor goes in is the cheapest insurance you can buy.
If you want the diagnostic reasoning behind this, the main home page has the overview of how we approach gate repair.
How to Save on Gate Motor & Opener
A few things you can do that pay off:
- Fix the gate before the motor fails. If the gate drags, catches, or reverses on its own, get it looked at before the operator burns out. A $150 weld is cheaper than a $1,300 motor.
- Get a free second opinion on any written estimate. Bring us the quote you got from the last outfit. If the number is fair, we will tell you so. If it is not, we will show you what we would do for less. That offer is on the table, no strings.
- Say the word on the discounts. Seniors and veterans get a permanent 10% discount. Any repair over $200 gets $40 off. No haggling, no coupon code, just mention it when you call.
- Ask for a repair, not a replacement. A lot of operators get swapped out when the board just had a bad capacitor. Ask whether the motor can be repaired first. We do not always say yes, but when we can, it is the right call.
- Keep the safety sensors clear. A dirty or misaligned photo-eye shuts the gate down. Cleaning the lens and checking the alignment is a five-minute habit that prevents a service call.
Call (833) 780-1547 for a free estimate – a live person answers, day or night. We do not have a voicemail box standing between you and a real conversation about your gate.
How a Gate Motor & Opener Service Call Works
Here is what actually happens when you call, so there are no surprises:
- You call and talk to a live person. We ask what the gate is doing: not opening, opening halfway, reversing, making noise, dead remote.
- We set a window and show up in it. No trip charge inside the county. A real appointment, not a callback range.
- We look at the gate first, not the motor. Post, hinges, track, rollers. A gate that fights the motor is the most common story we hear.
- We give you a number up front. Not a “we’ll see when we get in there” number. The number we say is the number you pay.
- If we can fix it on the spot, we fix it on the spot. On-site welding is in the truck. Parts are in the truck. The gate stays in your driveway.
- Every job carries the 90-Day Done Right Promise, in writing. If it is not right, one call brings us back. No runaround, no “that was a different issue.”
The whole job often wraps in a single visit. Replacement operators with a new access panel can take a second trip for wiring.
Is It Cheaper to Repair or Replace a Gate Motor in Enterprise?
Repair is cheaper in most cases – a repair typically runs $180 to $525, while a replacement runs $650 to $1,900. The math flips the other way when the motor is over 10 years old, the board is obsolete, or the operator cannot open the gate without stalling. For a 12-year-old operator with a bad board on a brand that no longer sells parts locally, replacement is the right call. For a five-year-old LiftMaster that just needs a limit switch, repair is. We will tell you which one you are looking at. Call (833) 780-1547 for a free second opinion on any written estimate.
FAQs – Gate Motor & Opener Cost
How much does a gate motor repair cost in Enterprise?
Most gate motor repairs in Enterprise run $180 to $340 for small parts like a limit switch, capacitor, or sensor. Board and receiver replacements run $260 to $525. A diagnostic call inside the county carries no trip charge, so the first number you hear is the number that matters. Call (833) 780-1547 for an exact quote – estimates are free.
How much is a new gate opener installed in Enterprise?
A new residential gate opener installed runs $650 to $1,450 for a slide gate and $900 to $1,900 for a dual-arm swing gate. Heavier wrought iron pushes the top end higher. If the gate needs welding or alignment first, add $150 to $400. Call (833) 780-1547 and we will give you a real number for your gate.
Can you fix my gate the same day?
Yes, in most cases, if the part is one we carry on the truck. Limit switches, capacitors, safety sensors, and most remotes and keypads get swapped the same day. A full motor replacement needs a match against your gate weight and brand, so it may schedule for the next available window. Call (833) 780-1547 to check availability.
Why did my gate stop opening when the motor still runs?
Usually the gate is the problem, not the motor. A hinge post that has shifted, a bent track, or a jammed roller will stop a working motor dead, and the operator shuts itself off to protect the gearbox. That is often the $150 to $400 welding-and-alignment range, not a $1,300 motor. Call (833) 780-1547 and we will look at the gate first.
What does gate access control cost to add?
A basic keypad or remote receiver runs $150 to $400. A full access panel with a card reader, intercom, or telephone entry runs $280 to $650 and up, depending on wiring. If the run from the house has to be trenched, that adds cost. Call (833) 780-1547 for a free estimate that includes the wiring.
Do you service the brand my gate already has?
Most likely, yes. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your operator is one of those, parts are often available locally and the repair is fast. If it is a builder-installed off-brand, we will tell you honestly whether it is worth fixing or replacing. Call (833) 780-1547.
Is there a discount on gate motor repair in Enterprise?
Yes. We have standing offers that do not require haggling: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Every job is stamped with the 90-Day Done Right Promise in writing. Call (833) 780-1547 and mention which one applies.
Why Homeowners in Enterprise Call Us Back
Most of the calls we get start the same way: somebody got a number on the phone from a big outfit and a different number at the door. That is the opposite of how we work. The number we quote is the number you pay, and if the job turns out different once we are in the driveway, we tell you before we pick up a wrench, not after.
We have been locally owned and owner-operated since 2001, which means our name is on the shop down the road and on every invoice. We are proud to serve the Enterprise community and the surrounding neighborhoods with gate repair, gate installation, gate motor and opener service, gate access control, and gate parts and welding. If the gate needs welding, we weld it on site so it stays in your driveway instead of getting hauled off to a yard across town. Our technicians have up to 25 years of experience, and every one of them is background-checked and comes to the door in uniform.
We answer the phone with a live person, 24/7. Not a voicemail, not a queue, not a chatbot. And every job is stamped with the 90-Day Done Right Promise: if it is not right, we come back. One call, no runaround.
Get a Free Gate Motor & Opener Estimate in Enterprise
If your gate is stalling, reversing, clicking, or dead, call (833) 780-1547 for a free estimate. A live person picks up around the clock. We will talk through what the gate is doing, give you a real dollar range before we come out, and show up in the window we promised. Senior and veteran discounts apply, repairs over $200 get $40 off, and there is no trip charge inside the county. You can also drive to the shop and look us in the eye – the name is on the building and the address is public. That is the oldest accountability there is.
Pricing reflects the Enterprise market as of 2026. Gatewood Fence & Gate Enterprise offers free estimates – call (833) 780-1547.
Written by the team at Gatewood Fence & Gate Enterprise.
What Our Customers Say
"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo