Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterGate Access Control Near You in Enterprise, NV
If you’re searching for gate access control near you in Enterprise, NV, the fastest path to a working gate is a phone call: (833) 780-1547. A live person answers that line 24 hours a day, 7 days a week – not a voicemail, not a queue three states away. We handle keypads, card readers, remotes, intercoms, and the openers behind them for homes and small properties across Enterprise and the surrounding valley.
Here’s what separates us from a national outfit: we’re locally owned and owner-operated, we’ve been at this since 2001, our address is published, and the license number is one you can look up yourself. Our technicians have up to 25 years of experience. Every job carries the 90-Day Done Right Promise in writing, and estimates are upfront, so the number you hear on the phone is the number you pay.
Key Takeaways
- A live person answers (833) 780-1547 any hour, any day.
- We repair and service nine major brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- No trip charge inside the county, and free second opinions on any written estimate.
- $40 off any repair over $200, plus a permanent 10% discount for seniors and veterans.
Fast, Local Gate Access Control
When a gate stops opening, you don’t want a week-long wait. We keep our schedule tight for Enterprise calls, and same-day service is often possible when you call before the afternoon. The person who answers will ask a few pointed questions about the gate, the opener brand, and what the keypad or reader is doing – or not doing – and that usually tells us what to bring so we don’t take two trips.
We know the neighborhoods here. In the older tracts off Windmill and Sunset, we regularly see access-control failures tied to summer heat cooking the control board inside an unshaded pedestal, and dust from spring winds gumming up the card-reader slot. Out toward the mountain edges, voltage drops during monsoon season are a common culprit when a gate opens halfway and stalls. Those aren’t guesses – they’re patterns we’ve watched repeat across Enterprise for years, and they shape how we diagnose on the first visit.
What you get on that visit: a real look at the whole system, upfront pricing before any work starts, and on-site repair wherever it makes sense. If the keypad’s fine and the opener’s the problem, we don’t sell you a new keypad. If a hinge post is loose and dragging the gate, we fix the post – because fixing the panel without the post just means you’ll fix it twice. Repairing what’s there is almost always cheaper and faster than replacing it, and we’ll tell you plainly when that’s true and when it isn’t.
For a deeper look at the systems themselves, see our Gate Access Control in Enterprise page, which walks through keypads, readers, and intercoms in more detail.
Areas We Cover
We work across Enterprise and the nearby communities, including Spring Valley, Paradise, Summerlin, Winchester, Henderson, Whitney, and Sunrise Manor. If you’re not sure whether your street is inside our service area, call and ask – the answer takes ten seconds. You can also start from our home page to see everything we do, or jump to a specialty repair like gate motor repair or automatic gate repair.
One thing worth saying about coverage: we don’t pretend to serve half the state. We serve this valley and the towns around it, which is why the truck that shows up is one that knows the roads, and why the person who answers your callback is the same one who was on the job.
What Gate Access Control Work Looks Like Here
Access control covers the parts of your gate that decide who gets in – the keypad, the card reader, the intercom, the remotes, and the wiring and opener that tie them together. Here’s the general order we work in when we arrive, so you know what to expect. This is a description of our process, not a guide to doing it yourself. Gate openers run on real voltage and the arms and hinges carry heavy loads, so leave the hands-on work to someone trained for it.
- Listen to the report. You tell us what the gate is doing – opening halfway, refusing the code, buzzing, or silent. That first description narrows the field a lot.
- Test power and voltage at the opener. Half the “dead keypad” calls in Enterprise turn out to be a supply problem upstream, not a keypad at all.
- Check the keypad or reader. We test the code, the reader, and the wiring into the control board. Heat and dust have a way of finding these first.
- Inspect the operator and the gate hardware. If the access device is fine but the gate still won’t move cleanly, the trouble is mechanical – a sagging hinge post, a worn roller, a bound track.
- Repair on site where possible. We weld and fix in your driveway rather than hauling the gate away. The gate stays put and you usually get it back the same day.
- Test the whole cycle and leave it working. We open and close it several times, check the safety sensors, and only then hand it back. The 90-Day Done Right Promise is stamped on the job in writing – if something isn’t right, one call brings us back.
If your system needs parts, from a replacement reader to a new remote, our gate parts and welding service covers that, and for new installs we handle gate installation from the post up.
What Gate Access Control Costs in Enterprise
Pricing is upfront, and these ranges give you a realistic picture before you call. Final cost depends on the brand, the age of the system, and whether the trouble is electrical, mechanical, or both.
| Service | Typical Range |
|---|---|
| Diagnostic visit (waived if you go ahead with the repair) | No trip charge inside the county |
| Keypad or remote reprogramming / replacement | $120 – $280 |
| Card reader or intercom repair | $180 – $450 |
| Control board / wiring repair | $200 – $500 |
| Opener or motor service | $250 – $650 |
| Full access-control system replacement | $800 – $2,500+ |
We don’t surprise you at the door. Before any work starts, you get the number in writing. And if you have an estimate from another company, we’ll give you a free second opinion on it – that’s a standing offer, not a special.
Why People Around Here Call Us
Most folks who reach us have already dealt with someone who quoted one price and charged another, or who never showed in the window they promised. Our answer is simple: the name is on the shop, the shop is down the road, and you can drive over and look us in the eye. We’re owner-operated, locally owned, and proud to have served these local communities for over 29 years.
We fix the gate in your driveway rather than swapping parts that don’t need swapping. If a gate is closing on its own, the trouble is usually in the hinge or the slope of the gate, not the opener – and that’s where we start. That repair-first approach is why our customers tend to call back the next time, and the time after that.
FAQs
How fast can you get to my gate in Enterprise?
Same-day service is often possible when you call earlier in the day, and after-hours calls are answered by a live person who can talk you through what’s happening and set up the soonest opening. We don’t put you in a queue and disappear. Call (833) 780-1547 and you’ll talk to someone now – estimates are free.
Do you serve my area near Enterprise?
We serve Enterprise and the surrounding communities, including Spring Valley, Paradise, Summerlin, Winchester, Henderson, Whitney, and Sunrise Manor. If you’re just outside those towns, call and we’ll tell you straight whether your street is covered. There’s no trip charge inside the county.
How much does gate access control repair cost in Enterprise?
Most access-control repairs run between $120 and $500 depending on whether the issue is the keypad, the reader, or the wiring and board. Full system replacements start around $800 and go up with brand and gate size. Pricing is upfront and in writing before we start. Call (833) 780-1547 for an exact quote – the second opinion on any written estimate is free.
Can you help after hours or on a weekend?
Yes. A live person answers the phone 24 hours a day, 7 days a week, and we schedule after-hours gate access control calls around the clock. If your gate is stuck open and you need it secured tonight, call and we’ll figure out the soonest we can be there. Estimates are free and the number takes a minute.
If you’re ready to get your gate working again, or you just want a straight answer about what’s wrong with it, call Gatewood Fence & Gate Enterprise at (833) 780-1547 for a free estimate. A live person will pick up, the pricing is upfront, and every job comes with the 90-Day Done Right Promise in writing.
Written by the team at Gatewood Fence & Gate Enterprise, serving Enterprise and nearby areas.
What Our Customers Say
"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo