Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateWhy Enterprise Homeowners Choose Ghost Controls Gate Repair
We provide independent Ghost Controls gate repair in Enterprise, NV: diagnosing controllers, arms, batteries, and accessory wiring on kits that owners installed themselves or inherited with the house. Our technicians have up to 25 years of experience with the brand, and we handle it as an independent service provider. We are not affiliated with, sponsored by, or authorized by Ghost Controls. That independence is the point. We troubleshoot across Ghost Controls, LiftMaster, Mighty Mule, and DoorKing without steering you toward a dealer-only replacement. A live person answers every call at (833) 780-1547, day or night. Every job carries the 90-Day Done Right Promise in writing, and the price is agreed before any work starts.
Why Trust Gatewood Fence & Gate Enterprise for Your Ghost Controls Gate Repair?
Our technicians have spent years inside Ghost Controls kits and know where these systems actually fail. Not on a generic opener chart. On the clevis. At the accessory terminal block. In a deep-cycle battery that reads fine at rest and collapses under load in July.
Because Ghost Controls is a DIY-oriented brand, most systems we see were wired by a homeowner on a Saturday. That wiring style leaves fingerprints: push-button and keypad terminals backed out a quarter turn, reversed polarity on an accessory, a control board that throws a fault code with no movement behind it. We read those signs before we touch a part.
We match arms, control boards, batteries, keypads, and photocells to the correct kit generation. Ghost Controls has changed controller layouts and accessory connectors across kit generations, and a board that fits a TDS single-arm kit is not the board that fits a TSS dual-arm system. We use OEM parts where they are the only reliable fit, and quality aftermarket for commodity items like batteries and hardware. Every repair is warranty-safe in the sense that matters: we don’t cut, splice, or rewire in a way that gives the manufacturer an excuse to deny a claim on a part that’s still under coverage.
Enterprise homeowners get a name they can verify and an address they can drive to. A gate sags in the hinge post, not in the middle – and that is where we start.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Common Ghost Controls Gate Repair Problems We Fix in Enterprise
These are the failures we see most on Ghost Controls systems around Enterprise, and what usually sits behind them.
- Bent or stripped arm actuator rod at the clevis (TDS and TSS kits). Wind load on a wide single-swing gate, or a gate that has drifted out of plumb, pushes the arm past its travel and the rod bends or the threads strip at the clevis pin. The opener then stalls mid-travel or grinds. Replacing the arm without checking plumb repeats the failure within a season.
- Controller faults from DIY accessory wiring. Ghost Controls kits come with push-button, keypad, and photocell wiring a homeowner runs themselves. Loose terminals at the AXPB push button or AXDP keypad, reversed polarity on an accessory, or a control board that shows a fault code with no gate movement. We meter the terminals before we order a board.
- Battery and solar-charge failure. The deep-cycle battery reaches end of life and the gate slows, reverses mid-travel, or beeps at the low-voltage threshold. Owners call convinced the controller is dead. It usually isn’t. In Enterprise heat, a battery that would last five years elsewhere often quits sooner, and it fails long before the operator does.
- Limit and soft-start/stop settings drifting after hinge sag. Hinge sag pulls the gate off its original geometry, so the limits no longer match where the gate actually stops. The gate slams, reverses on close, or trips the obstruction photocells on a clear driveway. Re-teaching limits on a sagging gate buys you a week; realigning the gate buys you years.
- Photocell and photo-eye sensor failures from sand and sun. The open desert edges of Enterprise throw wind-blown sand and grit, and summer highs over 100°F bake the sensor housings. A dirty or sun-cracked photo-eye reads a phantom obstruction and the gate reverses on close. It’s the first thing to check when a gate closes partway and backs up.
Ghost Controls Parts & Our Repair-vs-Replace Approach
We don’t stock Ghost Controls parts locally, and we won’t pretend otherwise. What we do is match the exact part to your kit generation: the right arm for a TDS heavy-duty single opener, the right board for a dual-arm TSS system, the right keypad and photocell for the accessory line you already have. For arms and control boards, OEM is often the only reliable fit. For batteries, mounting hardware, and clevis pins, quality aftermarket is fine and costs you less.
The honest part is deciding repair versus replace. When an arm is bent and the gate is also out of plumb, the truth is that replacing the opener fixes nothing. Fix the alignment and the hinges first, or the new arm bends the same way. Show me the gate closing on its own and I’ll show you where it’s failing.
Call (833) 780-1547 and we’ll give you a straight answer on whether your Ghost Controls unit needs a part or a plan. Estimates are free, and there’s no trip charge inside the county.
Our Ghost Controls Service Process – Step by Step
- 1
Diagnosis first. We check battery voltage under load, verify arm geometry against the gate’s actual swing, and test the photocells and keypad wiring at the controller terminals. A Ghost Controls fault code tells you a circuit tripped, not which part caused it.
- 2
Repair or install. We replace the failed arm, battery, board, or accessory, re-run sloppy accessory wiring to the manufacturer’s diagram, and realign the gate and hinges so the operator geometry is correct from the start. On-site welding means a sagging hinge post gets fixed in your driveway, not hauled away.
- 3
Test under real conditions. We cycle the gate through full open and close, re-teach the limits and soft-start/stop settings, and confirm the obstruction sensors trip and reset the way they should. Then we watch it close on its own – because that’s where the last failure showed up.
- 4
Warranty in writing. Every Ghost Controls repair we do is backed by the 90-Day Done Right Promise, stamped on the job, not buried in fine print. If it’s not done right, one call brings us back.
See the difference
Before
After
Before
After
Before
AfterGhost Controls Products We Service & Install in Enterprise
We service and install the Ghost Controls lines Enterprise owners actually have on their gates: the Heavy-Duty Single Gate Opener kits (the TDS series), the Dual Gate Opener kits and dual-arm systems (TSS), and the Architectural Series openers. On the accessory side we handle the AXDP keypad, the AXPB push button, the ABBT battery backup, photocells, and wireless entry transmitters.
That covers the full range of what a homeowner inherits or installs: a single swing gate on a side yard, a dual swing driveway gate, and the keypad-and-transmitter stack that makes the whole thing usable. Installation is measured and scheduled, not same-day – we come out, measure, and give you a written price before anything is ordered.
We Also Service These Brands
Ghost Controls is one brand in a much deeper bench. We’re certified to service nine major gate brands, including LiftMaster, Mighty Mule, and DoorKing, alongside FAAC, BFT, Linear, Viking, and Elite. That matters when your community gate shares an operator with a different brand than your driveway gate, or when a brand-specific part is back-ordered and a compatible alternative gets you working again without a full swap.
FAQs – Ghost Controls Gate Repair Service in Enterprise
No. We are an independent Ghost Controls service provider, not affiliated with, sponsored by, or authorized by the manufacturer. We work on Ghost Controls systems because we know them well, and we troubleshoot across brands without steering you toward a dealer-only replacement path. Call (833) 780-1547 with your model and we’ll tell you straight what we can do.
We use OEM Ghost Controls parts where they’re the only reliable fit – arms, control boards, and generation-specific components – and quality aftermarket parts for commodity items like batteries, clevis pins, and mounting hardware. We match every part to your kit generation so a TDS board doesn’t end up in a TSS system. Call (833) 780-1547 for a free estimate on your specific unit.
Most Ghost Controls repairs are a single visit, often same-day when you call in the morning. A battery swap, a photocell replacement, or re-teaching limits takes well under an hour. A bent arm plus a gate realignment runs longer, because we fix the hinge and plumb before we touch the operator. Parts that need ordering add a few days. Call (833) 780-1547 and we’ll give you a realistic window, not a guess.
We cover the Heavy-Duty Single Gate Opener kits (TDS series), the Dual Gate Opener kits and dual-arm systems (TSS), the Architectural Series openers, and the accessory line – AXDP keypad, AXPB push button, ABBT battery backup, photocells, and wireless entry transmitters. If you’re not sure which kit you have, read us the model number off the controller and we’ll sort it out. Call (833) 780-1547.
Proper service doesn’t void your Ghost Controls warranty, but sloppy work can – a cut harness, a spliced accessory line, or reversed polarity on a board can give the manufacturer grounds to deny a claim. We work to the manufacturer’s wiring diagram and document what we replace, so a part still under coverage stays covered. Call (833) 780-1547 and we’ll walk you through it before we start.
Most Ghost Controls repairs in Enterprise run roughly $150 to $450 depending on the part: a battery or photocell sits at the low end, an arm or control board at the high end, and gate realignment or hinge work adds to either. The price is quoted and agreed before any work starts – no surprises at the door. We take $40 off any repair over $200, there’s no trip charge inside the county, and seniors and veterans get a permanent 10% discount. Call (833) 780-1547 for an exact quote – estimates are free.
Usually not. A Ghost Controls gate that beeps and won’t move is typically reporting a low-voltage battery, a tripped accessory circuit, or a photocell it thinks is blocked – the beep is a warning, not a death rattle. We check battery voltage under load and meter the accessory terminals before anyone talks about a new operator. Call (833) 780-1547 and we’ll diagnose it properly.
Yes, in most cases, but it’s not just adding a second arm. A dual setup needs the right controller, a second arm matched to the gate’s weight and width, and synchronized limits so both leaves meet correctly. We’ll tell you honestly whether your existing kit can be expanded or whether a TSS dual-arm system is the cleaner path. Call (833) 780-1547 for a free assessment.
Because the gate drifted out of plumb, not because the arm is weak. Hinge sag, a shifted post, or wind load on a wide gate pushes the arm past its designed travel, and the rod bends or the threads strip at the clevis pin. Replacing the arm alone repeats the failure – the gate has to be realigned first. Call (833) 780-1547 and we’ll check the geometry before we sell you a part.
Start with the accessory terminals at the controller – monsoon wind and dust work loose connections and can reverse a wire at the keypad or receiver. After that, check the battery in the remote and whether the controller lost its learned codes. If the board itself took a surge, that’s a replacement. Call (833) 780-1547 and we’ll test the wiring rather than guess.
Yes, with realistic expectations. The ABBT battery backup and solar setups work fine in Enterprise, but summer highs over 100°F shorten deep-cycle battery life compared to cooler climates, and dust on solar panels cuts charging. A battery that lasts years elsewhere may need replacing sooner here. We test under load, not at rest, so you know what you actually have. Call (833) 780-1547.
Book Your Ghost Controls Service in Enterprise, NV
If your Ghost Controls gate is beeping, reversing, or stalled with one arm dead, call (833) 780-1547. We’ll diagnose the controller, arm, battery, or accessory wiring, realign the gate if it’s drifted, and replace only what failed – backed by the 90-Day Done Right Promise in writing. A live person answers, day or night. Estimates are free, and there’s no trip charge inside the county.
Written by the team at Gatewood Fence & Gate Enterprise.