Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Hinge & Roller Replacement: The Enterprise Owner’s Guide
We replace Ghost Controls gate hinges and rollers in Enterprise with parts matched to your exact model, and most jobs run $180 to $340 installed for a standard driveway gate. If your gate is dragging, squealing, or hanging off the post, we can usually look at it the same day you call and give you a written price before we touch a wrench. Our technicians have up to 25 years of experience, and every job is covered by our 90-Day Done Right Promise. Call (833) 780-1547 and a live person picks up.
Owners in Enterprise usually find this problem the same way. The gate stops latching square, or it scrapes the ground at the far end. Maybe the opener groans, then the safety reverse starts tripping on nothing. By the time it’s obvious, the hinge has been wearing for months. A gate sags in the hinge post, not in the middle, and that is where we start.
Key Takeaways
- Most Ghost Controls hinge and roller replacements in Enterprise run $180 to $340 installed, quoted before work begins.
- Worn hinges and rollers are the number-one cause of Ghost Controls openers that “work but won’t close right.”
- We match parts to your model by label and by measurement, not by eyeballing it.
- Your quoted price is the price. No surprises at the door.
Which Ghost Controls Models This Applies To
Ghost Controls builds its openers around residential swing and slide gates, and the hinge and roller parts we see fail come in two broad families: hinges for swing gates and rollers for slide gates. On the swing side, the models we service most in Enterprise include the single and dual swing lines, plus the heavier-duty arms that owners put on wider driveway gates. On the slide side, roller trolleys and the track-mounted assemblies are the common wear points. Ghost Controls openers are usually identified by a label on the control box or the arm housing, and that label tells us the arm model and the gate type. If the label is sun-faded, we measure the gate leaf and the hinge spacing instead.
Here’s the gotcha most owners hit: Ghost Controls sells hardware in configurable kits, and two gates that look identical can take different hinge sets depending on gate weight and post style. Buying the wrong kit online is a common and expensive mistake. When it comes to OEM versus aftermarket, we’re honest – the OEM hinge from Ghost Controls is a fine part, and a good aftermarket equivalent in the same size works just as well for a fraction of the price. What matters is the spec: pin diameter, plate spacing, and load rating. We’re an independent service provider and not affiliated with Ghost Controls, so we’ll tell you plainly which way makes sense for your gate. We also service LiftMaster, Mighty Mule, and DoorKing gates.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Hinge & Roller Replacement Is Failing
Most of what follows is a hinge or roller talking to you before it quits. Here’s what to watch for:
- The gate sags at the latch side. A worn hinge pin or a stretched hinge plate lets the leaf drop, so the latch misses its strike. Fix the panel without the post and you’ll fix it twice.
- The gate drags or scrapes the ground. When a roller flattens, the leaf rides low. Owners blame the ground or the driveway, but the roller is usually the culprit.
- The opener strains or reverses on its own. A stiff hinge fights the operator, and the opener’s safety system reads that resistance as an obstruction. A hinge problem can look a lot like an opener problem.
- Visible play or a wobble at the post. Grab the gate and rock it side to side. Any movement at the hinge is wear that will only get worse.
- Squealing, grinding, or metal-on-metal noise. Dry hinges and worn rollers make noise because the surfaces are meeting without grease or the bearing surface is gone.
In Enterprise, the weather works against these parts. Our summer heat bakes out grease and hardens bushings, and the wind that comes across the open desert brings fine grit that gets into hinge pins and roller tracks. That’s why we tell folks out here to check hinge play twice a year, not once.
Replacement Cost & What’s Included
Here’s how the pricing breaks down for Enterprise. These are typical installed ranges, and your written quote is what you pay.
| Job | Typical Installed Range |
|---|---|
| Single swing gate hinge replacement (pair) | $180 – $240 |
| Dual swing gate hinges (all four) | $260 – $340 |
| Slide gate roller replacement (set) | $200 – $300 |
| Hinge and roller together, plus alignment | $280 – $380 |
The range comes down to gate weight, how many hinges or rollers are involved, and whether the post needs reinforcement. Parts and labor are quoted together and agreed before any work starts. Every replacement we do carries our 90-Day Done Right Promise in writing – if it’s not done right, we make it right, one call brings us back. We also take $40 off any repair over $200, and there’s no trip charge inside the county. Seniors and veterans get a permanent 10% discount.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely check a few things yourself. Rock the gate to feel for hinge play. Look at whether the roller is flat or the track is worn. Grease the hinges and see if the noise quiets down. That much is fine, and it helps you describe the problem when you call.
Where DIY goes wrong is in the swap. A heavy driveway gate leaf, held up by hinges and no support, can come down on a person. Replacing hinges on a gate that’s still hung on its opener means the gate has to be supported, the opener has to be dealt with, and the new hinge has to be aligned to the post, not just bolted on. A lot of the gates we repair in Enterprise are ones where somebody tried it and got it close but not square. That’s how you end up fixing the same gate twice. If you’re going to try it, have two people and a way to block the gate up. If you’d rather not, call (833) 780-1547 for a free estimate.
FAQs
Expect roughly five to ten years from a good hinge or roller, and less in Enterprise where heat and grit wear them faster. Greasing them a couple of times a year buys you real years on the back end. When you notice play or noise, that’s your cue to call.
Sometimes. A dry hinge that just needs grease, or a roller that needs a new bushing, can be fixed rather than swapped. But a bent hinge pin or a flattened roller isn’t coming back. We’ll tell you honestly which one you’ve got. Call (833) 780-1547 for a free second opinion on any written estimate.
A hinge or roller set on a standard gate is usually a same-day job, done in a couple of hours. Larger or heavier gates, or gates that need realignment, can run longer. We’ll give you a clear time when we quote it.
We match your part to the model, by the label on the opener or by measuring the gate, then order the right hinge or roller for your setup. We don’t claim to carry parts on a truck, because we don’t. The part gets ordered to your gate, and we install it when it arrives.
Get Your Gate Working Again in Enterprise
If your Ghost Controls gate is sagging, dragging, or fighting its opener, we can take a look and give you a written price before any work starts. Calls are answered by a live person around the clock, and our name is on the shop in Enterprise – you can drive over and look us in the eye. We serve Enterprise and the nearby communities, and our technicians bring up to 25 years of experience to every job. Call (833) 780-1547 for a free estimate today.
Written by the team at Gatewood Fence & Gate Enterprise, serving Enterprise and nearby areas.