A Gatewood company - serving Enterprise, NV

Ghost Controls Gate Repair in Enterprise, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Gate Repair in Enterprise: What to Know First

We repair Ghost Controls gate operators and the gates they drive in Enterprise, and most jobs are diagnosed and turned around in a single visit. Pricing is quoted upfront and agreed with you before we start, so the number on the estimate is the number on the invoice. As an independent Ghost Controls service provider, we work on the brand every week but aren’t affiliated with or authorized by Ghost Controls.

Call (833) 780-1547

This page is for Enterprise homeowners who already own a Ghost Controls system and want it fixed right rather than sold a whole new operator. Call us at (833) 780-1547 and a live person picks up, day or night.

How Ghost Controls Products Fail – and How We Fix Them

Ghost Controls builds DIY-focused residential operators: the TDS series heavy-duty single and dual kits, the ARD automated residential series, and the LT light-duty line. They show up on driveways all over Enterprise, and they fail in ways that differ from a LiftMaster or a Mighty Mule. These are the patterns we see.

  • Battery and solar power falloff in the Nevada heat. The TDS and ARD kits run on 12V DC batteries, often charged by a small solar panel. Summer heat here cooks a sealed lead-acid battery faster than the owner expects, and the first symptom is a gate that opens fine at noon and stalls by dusk. We load-test the battery under an actual gate load, not just a voltage reading, then check the solar panel and charge controller before condemning the battery.
  • Control board water damage at the connector block. Ghost Controls control boxes sit at post height where irrigation overspray and desert wind-blown grit find them. The classic symptom is a remote that works only up close, or a gate that reverses mid-travel. That is usually corrosion at the terminal block, not a dead remote. We clean and re-seat the connections and seal the entry points correctly.
  • Arm mount and post movement on older gates. The actuator arm mounts to the gate and the post, and on a gate whose hinge post has leaned a quarter inch over a few summers, the arm binds and the operator throws an obstruction fault. Fixing the operator without the post is fixing it twice. We realign the arm geometry and address the post so the operator runs in its intended arc.
  • Limit switch drift and arm binding. A TDS unit that stops short or grinds at the closed position is often a limit switch that has wandered after months of thermal expansion. We reset the limits against the real gate position, then check the arm for worn bushings.
  • Battery-backed safety edge faults. The wireless safety edge that came with the system loses its pair or its battery, and the operator refuses to close. We re-pair the edge and confirm it stops the gate on an actual obstruction test.
Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Our Ghost Controls Gate Repair Process

  1. 1
    Call and describe it. Tell us what the gate is doing. A live person takes the call in Enterprise, and we set a window we will keep.
  2. 2
    On-site diagnosis. We test the battery under load, check the solar and charge path, inspect the control board connectors, and watch the gate move. Show me the gate closing on its own and I will show you where it is failing.
  3. 3
    The parts decision. Ghost Controls parts are widely available, but the aftermarket is full of near-fits. We use OEM where the part is a wear item or where a mismatch would affect the warranty, and a quality aftermarket equivalent where it is the same part at a fairer price. We tell you which and why before we order.
  4. 4
    The repair. Welding and alignment happen in your driveway. A gate sags in the hinge post, not in the middle, and that is where we start.
  5. 5
    The test. We run the full cycle, test the safety edge, and reset the limits against the actual gate travel. No guessing.
  6. 6
    The guarantee. Every job carries our 90-Day Done Right Promise in writing, stamped on the invoice. One call brings us back.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

What Ghost Controls Gate Repair Costs in Enterprise

Most single-visit Ghost Controls repairs land between $150 and $400, parts included where the part is a battery, remote, or small connector. Here are the ranges we quote most often:

Job Typical range
Battery and solar charging diagnosis and replacement $150 – $260
Control board cleaning, re-seating, and re-sealing $140 – $220
Arm mount realignment and hinge post repair $200 – $400
Limit switch reset and safety edge re-pair $120 – $200
Weld and rust repair on the gate itself $180 – $450, quoted after inspection

What moves the price is whether the gate itself needs work, whether the post has moved, and which parts we need. The quote is agreed before we start. Your estimate is free, and we offer a free second opinion on any written estimate you already have. Call (833) 780-1547 for an exact number.

Why Enterprise Homeowners Call Gatewood Fence & Gate Enterprise for Ghost Controls Work

We have been locally owned and owner-operated since 2001, serving local communities for over 29 years, with a published address and license number anyone can look up. The person who answers the phone is the person who shows up, and we carry the 90-Day Done Right Promise in writing on every job. Our technicians have up to 25 years of experience, and on a Ghost Controls gate that means knowing where the control board, arm mount, and battery actually fail in Enterprise conditions rather than swapping parts until something sticks. We service nine major brands including LiftMaster, Mighty Mule, and DoorKing, so if you have more than one gate on the property, we are already in the right truck. We also offer $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans, with no haggling required. A gate that will not close is not just an inconvenience. Call us and we will fix it.

FAQs

Does repairing my Ghost Controls gate void the warranty? No. Our repairs use OEM parts where a mismatch would affect the warranty, and we document every part we install. If you have a written estimate from another company, we will give you a free second opinion before you spend.

How fast can you get to my Ghost Controls gate in Enterprise? Typically same day or next day for diagnostic work, depending on the time of year. Call (833) 780-1547 and we set a window we will keep.

Do you have Ghost Controls parts on the shelf? We stock the common wear items and order the rest, usually a day or two out. We use OEM parts where the warranty matters and tell you when a quality aftermarket part is the smarter call.

Should I repair or replace my Ghost Controls operator? Repair is usually the right call if the operator is under about ten years old and the control board is sound. If the board is water-damaged and the motor is also failing, we will tell you plainly rather than nickel-and-dime you.

What does the 90-Day Done Right Promise cover? Every repair we do on your Ghost Controls system. If the same problem comes back within 90 days, one call brings us back at no charge, in writing.

Written by the team at Gatewood Fence & Gate Enterprise, serving Enterprise and nearby areas.

Need Gate Repair help nationwide? Licensed & insured · 30-60 min response · free estimates
Call (833) 780-1547
Local Service Coverage

Request a Free Estimate in Enterprise

Tell us what you need - Gatewood Fence & Gate Enterprise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch