Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Motor Replacement: The Enterprise Owner’s Guide
We replace failed Ghost Controls gate motors in Enterprise, and an installed replacement typically runs $650 to $1,150 depending on the model and whether the control board, battery, or solar setup needs anything beyond the motor itself. We can usually get out the same day for a dead operator, because a gate stuck open is a security problem, not an inconvenience. We’re an independent service company, not affiliated with Ghost Controls, but we’re certified to service their line and we know these motors well.
Most Enterprise owners find out the motor’s gone the same way: the gate hums and won’t move, or it starts creeping open a few inches overnight. Then the arm gets hot, the battery stops holding a charge past a day or two, and eventually the gate just sits there. In our desert heat, that decline is usually faster than the owner expects. When you call, we ask for the model number off the label and roughly how old the unit is before we head out, so the right replacement is on hand.
Key Takeaways
- Installed Ghost Controls motor replacement in Enterprise runs about $650 to $1,150.
- Same-day service is often possible for a dead motor; call (833) 780-1547.
- We’re an independent shop, not affiliated with Ghost Controls, and certified to service their operators.
- The heat in Enterprise shortens motor and battery life compared to cooler climates.
- Every job carries the 90-Day Done Right Promise in writing.
Which Ghost Controls Models This Applies To
Ghost Controls builds their single and dual swing operators around a few core lines: the TS series (TS1001, TS1011, TS1011X, TS1011L), the AX series (AX901, AX901X), and the dual-gate DS and TD series that pair two arms with a control box. The model number is stamped on a label on the underside of the control box or the back of the arm housing. Snap a photo of it and text it over, because the board revision matters. We’ve seen owners order a replacement arm for an older TS1001 that won’t plug into a newer control box without the matching harness.
For Enterprise, the practical decision is OEM versus a quality aftermarket equivalent. Original Ghost Controls arms carry the correct plug, the right solar input, and the current firmware. Aftermarket arms can be fine for a simple single-swing gate, but the control box has to recognize the arm’s limits and soft-stop behavior. If your controller is the newer AX or TD board, we stick with the OEM arm so the travel calibration holds and the gate doesn’t slam. If you’re on an older board that’s due anyway, that’s the moment to talk about replacing the whole operator rather than nursing an arm that’s out of production. We’ve made that call hundreds of times and we’ll tell you which side of it you’re on. The same logic applies to the other lines we service – LiftMaster, Mighty Mule, DoorKing – each has its own quirks, and Ghost Controls is no different.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Gate Motor Replacement Is Failing
- Gate hums but won’t move. The motor’s running but the gearbox or the arm’s internal drive is worn, so the torque never reaches the gate. When you can hear it working and the gate doesn’t budge, the arm is usually done.
- Gate creeps open or closed on its own. The limit switches or the control board have lost their calibration, or the arm’s internal stop is failing. This is the one that worries us most, because a gate that moves when it shouldn’t is a safety issue.
- Battery won’t hold a charge. In Enterprise’s summer heat, batteries that should last two to three years often go flat sooner. If a fresh charge only gets you a day of cycles, the battery is tired – but if a new battery still drains, the motor’s drawing more current than it should.
- Arm gets hot or smells like burnt wire. Overheating is usually a sign the motor’s working too hard against a sagging gate or a bad hinge, or the winding inside has begun to fail. We check the gate hang first, because a dragging gate will kill a healthy motor.
- Obstruction errors or random reversing. Sensors and the board’s reverse logic misfire when the arm’s position feedback goes bad. Sometimes it’s a dirty sensor; sometimes the arm’s encoder is on its way out.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Enterprise, an installed Ghost Controls motor replacement generally breaks down like this:
| Item | Typical range |
|---|---|
| Single-swing motor/arm (OEM) | $280 – $480 |
| Dual-gate motor pair | $520 – $850 |
| Control box or board (if needed) | $90 – $220 |
| Replacement battery | $40 – $90 |
| Labor (install, calibrate, test) | $180 – $320 |
So most single-gate jobs land around $650 to $850, and a dual-gate or full-operator swap runs $900 to $1,150. The range moves with what’s actually wrong: a clean arm swap is less than one where the control board and battery are also tired. We quote the price before any work starts, and the price on the quote is the price on the invoice. Every replacement carries the 90-Day Done Right Promise in writing – if it’s not done right, we come back and make it right.
DIY or Call Us?
A few things you can safely check yourself. Confirm the model number off the label, look at whether the gate sags at the hinge side when you open it by hand, and give the arm a gentle wiggle to see if it’s loose on its mounting bracket. You can also check the battery voltage at the terminals if you have a meter. What we don’t recommend is pulling the motor arm apart or getting into the control board’s wiring, especially if there’s a solar input involved. The arm holds spring tension and a charged capacitor, and that’s a jolt you don’t want. Gate operators also carry a crush and entrapment hazard, so the safety reverse and obstruction sensing have to be tested properly after any swap. That testing is part of every job we do, and it’s where a lot of DIY installs fail – the gate works, but it doesn’t stop when it should.
If you’re not sure, call us at (833) 780-1547 and we’ll walk you through what to look for before anyone climbs in a truck. No trip charge inside the county, no charge for the phone call, and a free second opinion on any written estimate you’ve already got.
FAQs
Plan on roughly 7 to 10 years in a cooler climate, but in Enterprise the heat is hard on them and we often see 5 to 8 years before the motor or the board gives out. Solar setups that run the battery hard tend to shorten that further. Call (833) 780-1547 for an exact quote – estimates are free.
Often, yes. If it’s the battery, the control board, or a loose bracket, we repair it rather than sell you a new operator. We fix a lot of arms that a swap-first shop would have replaced. Call (833) 780-1547 and we’ll tell you honestly which one you need.
A single-arm replacement usually takes three to four hours including calibration and safety testing; a dual-gate or full-operator swap can take most of a day. Most Enterprise jobs are done in one visit. Call (833) 780-1547 to schedule and get a time window.
We order the matching OEM arm or a quality aftermarket equivalent based on your model and control board, and we don’t pull a part until we’ve confirmed the label. We’re certified to service nine major gate brands, including Ghost Controls, so we know what fits. Call (833) 780-1547 and we’ll confirm the part against your model before we come out.
You’ve got a name you can check and a shop you can drive to. The name is on the shop, and the shop is down the road. Call (833) 780-1547 for a free estimate on your Ghost Controls motor replacement in Enterprise, and we’ll tell you straight what’s failing and what it costs before anything gets touched.
Written by the team at Gatewood Fence & Gate Enterprise, serving Enterprise and nearby areas.