A Gatewood company - serving Enterprise, NV

DoorKing Welding & Fabrication in Enterprise, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

DoorKing Welding & Fabrication: The Enterprise Owner’s Guide

If a weld has cracked on your DoorKing gate, the fix is an on-site repair, not a replacement. In Enterprise, we weld and fabricate DoorKing-compatible hinge posts, mounting brackets, and slide-gate frames in your driveway for about $250 to $900 installed, and most weld and bracket repairs are done the same day you call. You don’t load the gate onto a trailer and lose access to your property for a week.

Call (833) 780-1547

Owners usually find the problem the same way. The gate stops closing flush, or the latch misses by an inch, or you hear a pop when the operator engages. More often than not the failure isn’t in the motor at all. It’s a weld that let go at the frame where the slide gate meets its post, or a bracket that’s been quietly spreading stress through the operator arm for two summers. We weld on site, so the gate stays where it lives.

Which DoorKing Models This Applies To

DoorKing’s slide gates and swing operators take different mounting and fabrication work, so the first job is identifying what you’re actually working on. Your model number lives on a label inside the control box or under the operator housing. DoorKing slide gate operators like the 9000 and 9300 series use a different mounting bracket and chain layout than the swing operators in the 6000s, so a part that fits one won’t fit the other. Fabricated brackets for a slide operator’s pinch point won’t transfer to a swing arm, and vice versa. Measure the hinge post, the operator arm, and the gate frame thickness before you order anything. Frame steel on a residential slide gate is usually 14 to 11 gauge, and that range matters for weld fill and bracket fit.

The OEM-versus-aftermarket call comes down to what’s on the shelf and what’s safe. OEM DoorKing brackets carry the right hole pattern and load rating, but for structural fabrication – hinge posts, frame gussets, bolt-on reinforcement – a made-to-fit welded bracket often beats waiting a week on a factory part. We’re an independent service provider and not affiliated with DoorKing, and we price both paths honestly side by side.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your DoorKing Welding & Fabrication Is Failing

  • Visible cracks at the weld bead. A hairline crack in a hinge or bracket weld spreads under load and will fail completely before long. That’s the operator pushing against a joint that’s lost its strength, not a bad motor.
  • The gate sags at the hinge post. A sag starts at the hinge post, not the middle of the frame. The post weld or the bracket has taken the wear, and the whole gate has followed it down.
  • The operator grinds or strains at the same spot each pass. A binding frame or an out-of-line bracket loads the operator on every cycle. Left alone, it can cook a gearbox.
  • The latch misses and the gate won’t seat. A bracket that has shifted a quarter inch throws the alignment off and won’t close the gap. The latch isn’t failing – the mount moved.
  • Rust streaks at a joint. In Enterprise’s dry climate rust hides well, but Nevada’s cold desert nights cause thermal swings that let a failing weld start weeping. Rust bleeding at a bracket says the joint is moving.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Weld and fabrication repairs in Enterprise run $250 to $900 installed. A simple hinge or bracket weld on a residential gate sits at the low end; a full frame repair, post reinforcement, or a fabricated swing or slide mount lands nearer the top.

Job Installed Range
Hinge or bracket weld $250 – $400
Pinch-point or frame repair $350 – $600
Fabricated bracket / mounting $450 – $900

Every price is quoted and agreed before we touch the gate, and a steel-weld job takes a couple of hours to a full day depending on the frame. The work carries the 90-Day Done Right Promise, stamped in writing on the job. You get a free second opinion on any written estimate, no trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans.

DIY or Call Us?

Here’s where DIY almost always goes wrong. Welding a gate frame isn’t a driveway project for a homeowner – the loads are real, the steel is thin, and a cold weld on a hinge is worse than the crack you started with. Beyond no basic inspection, welding on a failing bracket with the operator still wired in is how you burn a control board. So what can you safely do? Check that all bolts are present, confirm the gate moves freely by hand, and look for visible cracks or rust at the joints – that’s it. Beyond that, call a pro. Call (833) 780-1547 for a free estimate.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 30-60 min response · free estimates
Call (833) 780-1547
Local Service Coverage

Request a Free Estimate in Enterprise

Tell us what you need - Gatewood Fence & Gate Enterprise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch