A Gatewood company - serving Enterprise, NV

DoorKing Keypad & Intercom Repair in Enterprise, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

DoorKing Keypad & Intercom Repair: The Enterprise Owner’s Guide

We repair and replace DoorKing keypads and intercoms in Enterprise, and a typical repair runs $185 to $340 installed, depending on whether the keypad, the intercom station, or the wiring in between is what’s given up. Same-day appointments are often open, and we answer the phone live around the clock. Most owners find out the hard way: the gate opens fine from the car remote, but the keypad by the pedestrian walk goes dead, or the intercom crackles and the visitor hears nothing back. That split – remote works, keypad doesn’t – is the first thing we ask about on the phone, because it tells us in ten seconds whether we’re looking at a button, a board, or a wire. We’re Gatewood Fence & Gate Enterprise, an independent service company – not affiliated with DoorKing – and DoorKing is one of nine major brands our technicians are certified to service.

Call (833) 780-1547

Which DoorKing Models This Applies To

DoorKing builds its access control in two lines that fail differently. The residential-and-light-commercial keypads (the 1500 series and its cousins, along with the older 1812 and 1833 units) are self-contained: buttons, circuit board, and sometimes a small LCD all inside one faceplate. When one of those dies, we’re usually swapping the whole faceplate assembly, because the buttons and board are potted together and there’s no clean way to replace just a keycap. The intercom side – DoorKing’s 1800-series entry systems and the standalone 1810 intercom stations – is a different repair entirely, because the audio board, speaker, and call button live in one housing while the wire to the house runs separately.

Here’s the compatibility gotcha that costs Enterprise owners money: DoorKing keypads come in flush-mount and surface-mount versions of what looks like the same unit, and the faceplates are not interchangeable. We’ve pulled a “matching” replacement out of a box more than once and found the screw pattern half an inch off. Before we order anything, we read the label inside the faceplate – it carries the model and the revision letter, and the revision matters – and we measure the existing cutout. On the parts question: DoorKing OEM faceplates are the safe call for anything still under warranty or on a multi-unit property where the property manager wants exact matching. For older units out of production, a quality aftermarket keypad with the same voltage and relay configuration works fine and costs less, but only if the relay logic matches. That’s the decision we walk through with you, not one we make for you.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your DoorKing Keypad & Intercom Repair Is Failing

If any of these sound familiar, you’re not imagining it and you’re not doing something wrong at the keypad.

  • Some buttons work, some don’t. The membrane or dome switch under a worn key has collapsed. It happens first on the digits of your own entry code, which is why it feels like the keypad “knows” and is just being difficult.
  • The keypad lights up but won’t accept a code. Power’s reaching the unit, so the feed is fine, but the control board isn’t reading input. Usually a board failure or water that got past a dried-out gasket and sat on the traces.
  • The intercom crackles, or you can hear them but they can’t hear you. A failing speaker, a corroded terminal, or a nick in the audio pair somewhere along the run. In Enterprise, our summer heat and the dust that comes with it dry out gaskets and work on exposed terminals faster than most of the country sees.
  • Visitors press the call button and nothing rings inside. The call circuit is open – a broken wire, a dead station, or a relay that’s given up. This one we can usually narrow down from the driveway with a meter before we touch a screwdriver.
  • The gate works from the remote but never from the keypad. The keypad’s relay isn’t closing, or it’s closing but the trigger wire to the operator has come loose. This is the single most common thing we’re called out for in Enterprise, and it’s often a fifteen-minute fix once we’ve traced it.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed pricing in Enterprise breaks down roughly like this. A straight keypad swap, flush or surface mount, runs $185 to $260. An intercom station replacement runs $240 to $340. Wire tracing and repair – when the unit is fine but the run to the house isn’t – runs $150 to $275 depending on how far we’re chasing it, and that’s the job that gets skipped by whoever was there before. Older out-of-production DoorKing models can run higher if we have to source a compatible faceplate.

The range is driven by three things: whether the wiring needs work, whether the model is current or discontinued, and whether we’re matching an existing multi-unit setup. You get the parts-and-labor number in writing before we start, and it doesn’t move. Every job carries the 90-Day Done Right Promise – if it’s not right, one call brings us back. And because it’s a repair, not an order-and-wait install, we can often get to an Enterprise keypad the same day.

Job Installed range
Keypad replacement (flush or surface) $185 – $260
Intercom station replacement $240 – $340
Wire trace and repair to the house $150 – $275

DIY or Call Us?

There’s honest, safe troubleshooting you can do before you call, and we’ll never talk you out of it. Pop the faceplate cover if it lifts off, look for water staining or green corrosion on the terminals, check that the wire nuts behind the unit are tight, and confirm the operator itself is working from a remote. That last check saves everyone time.

Where DIY goes wrong is the 12-to-24-volt low-voltage wiring and the control board itself. It’s not the shock that gets people – it’s crossed wires into a board that costs more than the keypad did, or a replacement unit whose relay logic doesn’t match the operator, which sends the gate into a loop nobody wants to watch. We’ve been called to clean up that exact mess in Enterprise more than once. If the cover’s off and you’re staring at a terminal strip, that’s the moment to call (833) 780-1547. The phone gets answered by a live person, day or night.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 30-60 min response · free estimates
Call (833) 780-1547
Local Service Coverage

Request a Free Estimate in Enterprise

Tell us what you need - Gatewood Fence & Gate Enterprise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch