Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Access Control Installation: The Enterprise Owner’s Guide
DoorKing access control installation in Enterprise usually runs $450 to $1,200 installed for a single entry point, covering the keypad or card reader, the control board or 6002 slide gate operator interface, wiring, and testing. If it’s a simple keypad swap on an existing operator we can often do it same day. Multi-tenant phone-entry or card-reader systems are measured and scheduled, with a written price before we start.
Most Enterprise owners find out something’s wrong the same way. The clicker stops working. The keypad only opens when you press it just right and lean on the gate. Or the gate just sits there, and nobody in the house notices for a day or two until a delivery driver starts honking. That’s the moment you call, and I get it. Access control is the part of a gate you touch every single day, so it’s usually the first thing to give out, not the last.
Which DoorKing Models This Applies To
DoorKing builds access control around a few families, and knowing which one you have saves a lot of guessing. Common in Enterprise:
- Series 1833, 1835, 1837, 1838 – telephone entry systems. If yours reads “1835” or “1838” on the front panel label, it’s a phone-entry unit that ties into an apartment or estate intercom.
- Series 1500 and 1510 – standalone keypad units, often the older workhorses.
- Series 6002 slide gate operator and 6400 swing operator – the operator itself, with the access control wiring landed at the terminal strip.
- Series 1810 and 1812 access controllers for card and fob systems.
The exact label is usually on a metal plate inside the cabinet door, and on the operator near the terminal block. Look at the plate before you call, or send me a picture. It saves a second trip. As an independent local gate specialist, I’m not affiliated with DoorKing, so I don’t push their OEM parts. A quality aftermarket keypad can get a failing unit back in service and drop the installed cost by $150 to $400. But for the telephone entry units, OEM is usually the better call. Their proprietary wiring and the housing tolerances aren’t matched well by aftermarket. That’s the honest split.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Access Control Installation Is Failing
The symptoms tell you what’s actually gone bad, which is useful before anyone shows up.
- Gate only opens when you press the keypad with unreasonable force. The keypad’s membrane switches are worn. It’s a keypad problem, not a wiring problem. Replacing the keypad is usually the fix.
- The remote works from a distance but not up close. The receiver or its wire is failing, or the antenna has been kicked or replaced with something wrong. Common in Enterprise where the fence post gets hit by the mower.
- The gate stops mid-travel and reverses. The limit switch, the safety loop, or the control board’s logic is confused. This isn’t an access-control fault; it’s the operator. Get it checked before it damages the drive.
- Nothing works, no lights on the board. Power or the board itself has failed. This is the one that usually needs a real technician with a meter on it.
- Keypad beeps but the gate doesn’t move. The board isn’t receiving the signal. Terminal, relay, or the operator’s wiring. Less common in Enterprise and worth a look before you buy parts.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what it usually costs to get access control back online in Enterprise. Prices are estimates, not quotes. Your exact price gets written down before any work starts, and I don’t add anything on at the door.
| Work | Typical Installed Cost | What It Covers |
|---|---|---|
| Keypad replacement (existing operator) | $280 – $520 | New keypad, wiring to existing control board, programming, testing |
| Card reader or fob system install | $550 – $1,100 | Reader, controller, low-voltage wiring, programming, test |
| Telephone entry system like 1835 or 1838 | $900 – $1,800 | Unit, mounting, wiring, line connection, programming |
| Full new access control for a new gate | $1,400 and up | Controller, entry hardware, wiring, operator integration, test |
The range depends on the operator model, whether power is already at the gate post (that’s a frequent surprise in Enterprise), the number of entry points, and whether the wiring is good or needs to be re-run. The price you’re quoted covers the parts and the labor, and if the gate needs a new control board too we tell you before we start, not after. The work carries our 90-Day Done Right Promise in writing, and if I have to come back over something I got wrong, I come back.
DIY or Call Us?
Some of this you can check. Some of it you shouldn’t touch.
Safe things to do: press the keypad and watch the board’s LED for a signal light, check that power is on to the operator, and look for obvious wire damage at the gate post. That’s it.
The part I’d leave alone: anything that opens your panel or goes into the operator cabinet. That’s where live low-voltage wiring sits right next to the main power feed and the operator’s drive circuitry. A meter in the wrong spot or a short across the wrong terminals can blow the board and it can knock you off your feet. I’ve been called out too many times to a gate where someone tried this and turned a $400 repair into a $1,200 one. Call (833) 780-1547 and we’ll look at it. Calls are answered by a live person, 24 hours a day, not a voicemail or a call center three states away.
FAQs
How long does DoorKing access control usually last in Enterprise? A keypad typically goes 7 to 12 years; a control board 8 to 15, depending on conditions. Our desert climate and the summer heat around Enterprise shorten that some, and sun exposure on the cabinet bakes the electronics inside. Replacing parts on schedule beats replacing the whole unit.
Can the part be repaired instead of replaced? Sometimes. Keypads can be cleaned and re-seated. Boards can be checked for loose terminals or blown fuses. What I don’t do is swap a $30 fuse into a board on its last legs and tell you it’s fixed. Call (833) 780-1547 for a free second opinion, and I’ll tell you honestly if it’s a repair or a replace.
How long does the swap take? A keypad swap or a board replacement on an existing operator is usually a 2 to 4 hour job. Telephone entry units take longer, half a day or more. A new multi-point system for a fresh installation is measured and scheduled, so we can order the right parts before we show up.
How do we source the part? We match your model number from the plate and order OEM when it matters (telephone entry units) and quality aftermarket when it doesn’t. We don’t carry stock and we’re upfront about lead times. When we say a part’s in, it’s in.
We also service LiftMaster, Mighty Mule, and Ghost Controls if you’ve got more than one gate on the property.
If your gate won’t open and you’ve tried the obvious, call us. We’re in Enterprise, we answer the phone 24/7, and the name is on the shop down the road. Call (833) 780-1547 for a free estimate. If you’re a senior or a veteran, that 10% discount is permanent, and it’s yours without asking. If you’ve got a written estimate from another shop, we’ll give you a free second opinion on it. That’s not a sales pitch, it’s just good business.
Written by the team at Gatewood Fence & Gate Enterprise, serving Enterprise and nearby areas.