Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Welding & Fabrication: The Enterprise Owner’s Guide
Welding and fabrication work on a Ghost Controls gate in Enterprise usually runs $180 to $420 for a repair like a re-welded hinge post, a rebuilt mount bracket, or a re-plumbed arm anchor, and we can often get to it the same day you call. Full fabrication (a new frame section, custom brackets for an uneven driveway grade, or a re-hung cantilever setup) is measured and quoted, typically $500 to $1,400 depending on gate size and how much metal has to come out. The reader who lands on this page usually found it the hard way: the gate got stiff, the arm started grinding, or a hinge post wiggled loose in the caliche, and they traced it back to a weld that finally gave up.
Key Takeaways
- Most Ghost Controls “opener problems” in Enterprise are actually weld or bracket problems in disguise.
- We weld on site, in your driveway, so the gate stays put.
- We’re an independent shop, not affiliated with Ghost Controls, and we say so up front.
- Every job carries the 90-Day Done Right Promise in writing.
Which Ghost Controls Models This Applies To
Ghost Controls builds its automation around single and dual swing gates, and their common residential lines are the TSS1 single, the TDS2 dual, and the heavier AXS/AXD and DTP1 packages. The welding and fabrication work is not model-specific in the way a control board is; what matters is the gate frame and the mounting surface. But the model does change how the bracket has to be fabricated, because a TDS2 dual-arm kit loads the hinges and the center post differently than a single TSS1 does, and Ghost Controls’ arm anchors are spaced to a specific geometry that a homemade bracket will miss if nobody measures it. The rear-mount bracket height and the arm pin distance are the two gotchas. If the gate frame is thin-walled tubing (under about 14-gauge), the arm will flex the frame before it flexes the bracket, and the weld will fail at the toe of the joint rather than the bracket itself.
To identify what you have, read the data plate on the operator housing (it lists the model and a serial) and photograph the hinge and mount areas before you call. OEM Ghost Controls brackets are galvanized; a quality aftermarket fabrication shop can match the geometry in mild steel and hot-dip or cold-galvanize it, which is often the better call in Enterprise because it lets us fit the bracket to the actual post rather than the nominal one. We don’t stock parts and we don’t carry them on a truck. We measure, source, and fabricate to what your gate actually is.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Welding & Fabrication Is Failing
The gate rarely tells you the weld is going. It tells you the arm is working harder than it should. These are the symptoms we see most in Enterprise:
- The gate binds or drags in one spot. That is almost always a hinge post that has cracked at the weld toe or pulled from the concrete, not a hinge pin that needs grease. The arm then fights the bind and the operator limps or stalls mid-travel.
- The arm mount bracket is bent or the bolt holes are wallowed. A bracket that has flexed has lost its geometry, and the arm will now push the gate off-axis. Welding a new bracket is cheaper than replacing the operator you’ll burn through if you don’t.
- The gate sags at the latch side and the arm strains to close it. A sag lives in the hinge post, not the middle of the frame. If we fix the panel without the post, we fix it twice.
- You see rust streaks or a hairline crack along a weld seam. Enterprise sits in a high-desert climate with big day/night swings and summer heat over 100°F; thermal cycling works a marginal weld loose over a few seasons, and once moisture gets in, the crack grows.
- The gate frame is racked (corners out of square). Racking transfers load into the operator’s arm and travel limits, and no opener adjustment will fix it. The frame has to be pulled square and re-welded, or a new frame section fabricated.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the honest range for Enterprise, and the price is quoted and agreed before any work starts. It doesn’t change at the door.
| Job | Typical installed range |
|---|---|
| Re-weld a cracked hinge post or gate frame joint | $180 – $280 |
| Fabricate and weld a new arm mount bracket | $220 – $340 |
| Re-plumb and re-anchor a hinge post (concrete included) | $300 – $480 |
| Pull a racked frame square and re-weld corners | $350 – $650 |
| Fabricate a custom bracket set for uneven grade | $400 – $800 |
| New frame section or cantilever re-hang | $500 – $1,400 |
What drives the number: how far the post has pulled, whether the concrete is sound, gate weight, and whether the bracket has to be measured on site. We weld on site, so you’re not paying to haul the gate off and back. Every job carries the 90-Day Done Right Promise in writing. Standing offers: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans.
DIY or Call Us?
You can safely do a few things without a welder. Grease a stiff hinge pin, tighten a loose bolt, clear debris from the gate’s path, and check that the control box is powered are all fine. What you should not do: weld on a welded gate frame yourself unless you’re a competent welder, because a bad weld creates a hidden crack risk that shows up at the worst moment, and welding near a powered operator can fry the board. And anything involving a high-tension spring, a counterweight, or a gate over head height is a genuine injury risk – those stay with a trained professional. That’s not scare language, it’s the truth of the work. If you’re not sure, the answer isn’t on the internet. Call us at (833) 780-1547 and we’ll tell you straight on the phone what’s likely wrong and what it’ll cost.
FAQs
A sound weld on a properly fit bracket should hold 10+ years. The failures we see in Enterprise cluster around 4 to 7 years, and they’re almost always fit problems (bracket not mated tight to the post) or frame problems (thin tube, racked gate) – not the weld itself.
Yes, in most cases. We’d rather weld the bracket that’s there than sell you a swap. We only replace when the frame is so racked or the post so pulled that the repair wouldn’t hold. We’ll tell you which before any work starts, in writing.
A bracket replacement or a hinge re-weld is typically 1 to 3 hours on site. A frame pull-square or custom fabrication may take a half-day or a scheduled second visit. Your free measure and written price happens first, and same-day repair is available.
We measure the actual gate, source the OEM bracket when it fits, or fabricate a match in hot-dip or cold-galvanized steel when it doesn’t. We don’t stock parts, so the part is ordered or made for your gate, not pulled from a shelf hoping it fits.
If you’ve got a Ghost Controls gate in Enterprise doing something it didn’t do last year, call (833) 780-1547. We’ll give you a free estimate, tell you what we actually think is wrong, and if it’s a weld we’ll bring the truck and weld it right there in your driveway. A live person answers around the clock, and the price we quote is the price you pay.
Written by the team at Gatewood Fence & Gate Enterprise, serving Enterprise and nearby areas.